Search results for query: *

Please tell me which site is offering practice test for 642-902. I have used www.how2pass.com in the past for my CCNA, but 642-902 is yet to be available in the web site www.how2pass.com. If any of you have already taken the exam please let me know which website u have used to practice. Thanks...

Hello Friends, I have a question on configuring two bootprelays for two different DHCP servers that reside on two different VLANs for example: DHCP server 1 on VLAN X, DHCP server 2 on VLAN Y. There are two set of clients one set of clients residing in VLAN A needs to use DHCP serever 1 in...

Hi, Can some one help me with congestion control on ethernet frames. How can I discard the frames when there is a congestions. Voice traffic shouldn't be dropped, but the data traffic can be dropped. On a layer 3 we have DSCP markings. Thanks, Neto

Hi, Can some one help me with congestion control on ethernet frames. How can I discard the frames when there is a congestions. Voice traffic shouldn't be dropped, but the data traffic can be dropped. On a layer 3 we have DSCP markings. Thanks, Neto

Hi Geeks, Its a simple ques?, but I don't know the answer. Why do we need a native VLAN on a trunk other than specifying the port as Trunk mode. Neto...!!

Hi Guys's, For a Classless IP for example 192.168.0.0/27, the assigned IP addressess would be from 192.168.0.0 to 192.168.0.31 . Since 192.168.0.0 is a subnet IP address, I know we can't use it to assign any host with that IP. How about the last IP in the subnet 192.168.0.31, is there any...

Hi Guys, Can some one explain the difference between Fast Ethernet and Ethernet. Neto... "you are running fast to remain in the same place

Hi Guys, I have seen people talking about L2 and L3 communication. But when it comes to extreme I have seen people mentioning about Extreme as a L2 bridge and gives it no respect for its L3 capability. My question is if one side of the Extreme is connected to the Router were it will have to...

I have loaded the Extreme 48Si with configuration. Now I want to add a new static route to the switch. I can load the static route, I don't know how to save the config after loading just one sentence. I did it once using save prim config and it overrote my existing config. Help me guys,

How does the access-profile work, here there is case where the extreme summit48si is connected to a Cisco 2950 Layer 2. Cisco 2950 Layer 2 is then connected to a Cisco 2801 running IOS and OSS Server engine. CISCO 2801 and OSS Server are both in different subnet. When I configured the extreme...

guys, What is fdb used for. Where will the database be forwarded by default. Neto...........

Guy's, If a port is added to the VLAN and if the port is not configured for auto-on or auto-off, what would be the default configuration on the ports. Neto.......

Guys, Will this cause routing issue. The Y named VLAN has subnetmask of xxx.xxx.202.0/25 and the access-list created for the same Y VLAN is xxx.xxx.202.0/26. The subnet mask created are different. But the IP address used in the LAYER 3 Switch from these VLAN's are xxx.xxx.202.1/25 and...

I have a situation were the assigned default gateway for a particular switch is outside the subnet of the switch itself. The default gateway is always the next-hop, but the issue is that we do create access-list based on the subnet and in the above case the gateway is outside the subnet. Will...

Hello Guys, config sharing address-based L2_L3_L4 any one explain me what this command is used for? Neto....

Can any one explain about for what a TFTP server is used for??? Neto....

Hi, What is the commad used to take a look at the Daylight Savings and Time on the Summit 48Si, Thanks Neto....

Hi, The LAN switches is configured with two SNTP servers and the SNTP-client is enabled. Will this take care of time in the LAN switch. " My question is that do I need to use the "configure time" commands also inorder for the LAN switch to synchronize properly." One more question, The LAN...

Hi All, If a SNMP trap is configured with community name "xxxxx", and there is a readonly community "xyxy". Does it prevent the snmp manager to read the configured snmp trap. I don't know whether it is a stupid question or not. But any way advice me on this thanks... Netomaniac....

Hi All, Is there a way to find the MAC address of the Extreme summit 48si switch. Thanks....