Search results for query: *

Hi, just wondering if anyone has got the Calendar function to work in CUEAC from CUPS/Exchange?

Hi all, Another SRG50 question im afraid, the bane of my life these things, CS1K engineers always say it’s the srg not the cs1k lol. Problem is I have 5 srg50s and 1 is having a problem with incoming calls that have the number withheld. The call comes in on to the srg s BRI and it tries to...

Hi, I have 5 srg50 rls 1 installed around the country and have been working fine for ages, three weeks ago they all start complaining of dead calls now and then. I have found out its only when a srg set calls a mobile or a landline number that is busy. The srg sets are no longer receiving bust...

Hi all, I’m building a new BCM200 and will be networking it to a CS1K in the US via SIP. My DN range starts at 2700 and I need to route the following: 20A, 21A, 22A, 23A, 24A, 25A, 26A, 28A, 29A, 3A, 4A, 5A, 6A, 7A. I am able to build all the des codes above apart from 28A, I have looked...

Hi all, I’m having an issue with any BCM 3.7 drive I image with the Nortel BIT software. The Apache service will not start-up! I have found the following and downloaded the files need but does anyone know the procedure with the files? BCM 3.6 or BCM 3.7 has been bit imaged. However, since...

Cant seem to find any info in the documentation on if you can search the bcm extension numbers in the corp directory from the wireless&Dect handsets on a bcm 3.7 or 4.0, anyone know?

Hi, Is it possible to use names instead of numbers on the IP KEM attached to a I2004 on a bcm200 v4.0. I cant find any information in any of the documentation. I know you can through telephone options on the handset but thats only on the cs1000. Any help would be great.

As title, can i have 4x DTM in as long as i have the BUS's free?

Has anyone installed a BST doorphone on an SRG v1.5, do they work? Any problems with them? Any help would be great.

I have a issue where a bcm50rls1 calling bcm400 ver4 over voip trunks calls always end up at the reception primeset. Bcm50 is sending 4 digits and i can see the digits come in on the 400. All the target lines are setup ok and the private received length is ok. Any thoughts?

Does anyone know why when I enter the corporate directory on an ip phone or tdm and I enter the name it only shows stars instead of letters? System is a BCM400 ver 4.

How can i show the first 6 PRI lines on a I2004 with Expansion mod. I have no idea how to get this to work...Pls help

Hi all, I installed a SRG400 and the site have a tannoy system that they want on the srg, tannoy is a Eagle TPA30P. I tried to put it on an analogue port but all i got was ringing over the tannoy lol. I was thinking of putting a GATM4 in and putting it on that, has anyone insatlled a PA sys on...

Hi all, I installed a bcm 400 v4.0 the other day with a dass2 interface, all the DDI numbers are working fine and going to the right sets but im not seeing any CLID on the incoming calls to the phones or in BCM monitor. I have the Caller ID Set box ticked on the target line. Can anyone point...

Hi, I hope this will be a quick question. Is there anyway i can change the 88 access code for the remote access to vm?

Hi all, Im getting an issue on a few srg's that when a phone on the srg is forwarded to the voicemail system on the CS1k 1 in 4 calls that get transfered connect but a silent msg is left and i get the following error msg on the srg: 53009 critical ResourceMediaController::(OID=0x10166dc8)...

I need to setup on a bcm 3.7 a schedule so between 5:00am and 3:00pm incoming calls to the bcm that begin with 009 are forwarded to a mobile. Anyone know what i would need to programme on the bcm to get this working, if it can. Regards CX

Hi all, I have a problem with an SRG50 rls 1 fully patched where im getting a 5 sec delay in speech when the set is answered after the delay the call is perfect. In local mode I don’t get this issue? I have installed seven srg’s and only have this problem on 2 of them, all setup the same way...

Hi, I have a bcm 400 v4 and im having trouble changing the password for nnadmin, i have set it to user must chg password at next login and now i get the "you must chg your password" screen "Welcome" no matter what i chg the password to it will not take it. Everytime i chg the password and...

Im having trouble with 2 analogue set on an srg 50 rls1, i cant get them to dial a 4 digit ext number on the cs1k without having to put the trunk access code first i.e 8xxxx i just want them to dial ext xxxx. Does anyone have any ideas? Regards CX