Search results for query: *

Hi, We are interconnecting a 2960 equiped with a cisco 100MB FX SFP to a 2950C. We get errormessages telling me there is a duplex mismatch: 00:36:48: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet0 /2 (not full duplex), with ASW2 FastEthernet0/25 (full duplex). I have...

Hi all, I am trying to setup 3 Vlan's and ports on 2 switches. What I have done: switch#1: vlan1(default), Vlan2, vlan3 switch#2: vlan1(default), Vlan2, vlan3 switch#1: port 1/0/1, hybrid, untagged vlan2, tagged vlan3 port 1/0/2, hybrid, untagged vlan2, tagged vlan3 communication between port1...

Hi all, I have a question about sip trunking from a BCM50R3 to a CS1K NRS. This is all new to me so forgive me if it's a dumb question. We have enabled 4 sip trunks at the BCM50. We use a 4 digit numbering plan. What we need is to be able to call another site which has a 4xxx internal numbering...

Hi all, I am having problems stacking BES220-48T-PWR switches. What I have done: - checked if firmware of both are the same: OK - Set switch 1 at the back to "base" - Connected both switches from up-to down port and from down-to up port. In other words I created a loop. (according to the manual)...

We are unable to register 12xx sets to a BCM450. The problems we encouter are as follows: BCM is setup as DHCP server. registering 11XX sets => no problems registering 200X sets => no problems registering 12xx sets => trouble When connecting the 12xx set the set displays information: Loading...

At the moment we are configuring a BCM450 and we encounter some problems: We have a BCM 450 loaded with a DTM module and a BRI module. According to the documentation we have to assign lines to the modules which we did: DTM (Main MBM4) => lines 91-120 BRI (Main MBM3) => lines 61-68 All...

Hi, I had a problem connecting 2 switches together. This is the situation: one new 2960 switch, port f0/24 not configured in trunking mode. Just a standard port. Only this port is assigned as switchport access VLan200. The reason is that the first 12 ports are VLAN100 and port 13to24 is VLAN200...

We have a site running a BCM50 R2.0 with WLAN 2211 handsets. On a digital or IP set people can use feature 0 to use speed dial. How can this be done at a 2211 handset? Maybe I overlook it but I can't find the use of features Thanks in advance for any help.

Hi, We have a BCM1000 v2.5 Our mainoffice tel.number comes in at targetline 241 wich is handled by our receptionist (operator). Is there a way to create a ringschedule say "night" where all calls at TL241 will be redirected to a predefined external number? Ofcourse use of F84 is possible but...

Hi, We have a BCM1000 v2.5 using a PRI (Euro) What we want is to prevent sending OLI. Is there a setting where we can disable sending out number systemwide? Using F819 works well but it is a "per call" and "per DN" feature. What we want is a systemwide setting to prevent sending...

Hi Earlier I posted a thread with a question about changing settings for UPS and BCM. After testing I have some suggestions wich you might can use to change settings. We use a APC 3000VA UPS on a BCM400. This means that in case of a power failure the BCM can run at least for about 3 hours...

Hi Folks! I know it's been an issue before but I am stuck here. We have a BCM 400 running with the latest patches. We connected an APC SURT3000 UPS to the system and started testing (after full charging) We have found out that after about 15 minutes the BCM will shutdown. Is there a way to...

Hi I am quite new to full loaded BCM400. Any suggestions to pay special attention to or considerations regarding setup and performance? BCM400 is loaded with: ASM8+ module (bus 2) ISDN BRI module (bus 4) 2 x DTM module for 2 x PRI (E1) (bus5+6) 80 IP sets (2002 and 2004) Proffessional Call...

Hi all, Can someone tell me why I cannot configure a huntgroup as primeset for a targetline? What I try to do is assign a targetline to an extension, say TL241->Ext.221 If 221 does not aswer within 4 rings I want overflow into a huntgroup say HG01. (HG01, broadcast to 10 members) My Other try...

Hi, I am trying to set up a situation using the automated attendant as a backup for the operator. What I want to do is: incoming targetline 241 rings at operator ext.200 Call Pilot automated att. is set up to answer after 8 rings and will give a message like "all operators are busy, please hold...