Search results for query: *

Hi, Does anyone know how to "force" CallManager to create a UDL file? or where this file lives? I have done a file search on the CallManager server and can't find it anywhere. Thank you

Hi, Has anyone out there successfully linked AI Office to Cisco CallManager 4.2? Aparantely I have to link the AI Office collector to a .udl file created by CallManager. I have done a search for any such a file on the CallManager server but there are none. Anyone has any ideas about how...

Hi, I wonder if anyone could give me some light regarding the following In one site I have a 2811 and in the other site I have a 2811 with a PIX506E. Both routers are running CallManager Express with IOS versions: c2800nm-adventerprisek9-mz.124-4.XC4.bin...

Hi, We have Cisco CallManager Express installed in one of our sites and I was wondering if the following would be possible... The customer has a GFI Fax on-site, can I route the traffic to this GFI Fax through a Modem WIC-2AM card and if yes, I would appreciate some hints for the...

Hi, I have a 7914 Expansion module installed next to my 7960. The expansion module seems to be working fine ... besides the lights... According to Cisco documentation the lights should do as follows: Off/dark Line available Green, steady Line in use by you; you may also transfer the call...

Hi, I am trying to get an expasion module 7914 to work with my 7960. These are some extracts from my config: CONFIG (Version=4.0(1)) ===================== Version 4.0(1) Cisco CallManager Express load 7914 S00104000100 load 7960-7940 P0030702T023 At the moment when I go into the...

Hi, I have recently installed two Cisco 857W wireless routers and after installing them at two different houses, I am having exactly the same problem in both instances. The problem I am experiencing is the lack of signal as soon as I move into a different room/floor. In one of the cases, I...

Hi, I am expereincing the following problem with a Cisco 1701, flash:c1700-advsecurityk9-mz.124-5.bin. I telnet into the router, type the terminal monitor command and then the fun begins...... if I do a "debug ip icmp" and do a ping somewhere I get the following... TEST#debug ip icmp...

Hi, I need to load balance traffic from one router over two ADSL lines but I only have control over the on-site router, not over the ISP router. Is there a way of doing this...I've been reading trying to find some information regarding the subject but in all the papers they seem to think...

I have two 837s running HSRP. Both routers are connected to a 2960. Router_1: interface Ethernet0 ip address 192.168.0.2 255.255.255.0 no ip redirects standby 1 ip 192.168.0.1 standby 1 timers 254 255 standby 1 priority 111 standby 1 preempt hold-queue 100 out Router_2: interface...

Hi, I'm running HSRP in a small LAN.... I am using two 800 series which are connected to a 2960Switch... the configuration in the routers is as per below.... For Router-2: interface Ethernet0 ip address 192.168.0.3 255.255.255.0 standby 1 ip 192.168.0.4 standby 1 priority 200 standby 1...

Hi, I am using a 2811 and a 2621 to simulate a network. I have configured the 2621 to be the LAN router and the 2811 to be ISP. On the 2621 I have configured some route policy which establishes that all traffic that comes from network 192.168.82.0 is to leave the router by interface fa 0/0...

Hi, I have a 2621 with a WIC 1B S/T card and a 2811 with a WIC 1B S/T V3 card I have connected the two ports with an ethernet cable and configured the 2 Interfaces but I can't ping neither of the interfaces......is this because I don't have a "proper" D channel??? Is there anyway of...

Hi, need some help with this please... I have a router 2600 series which has 2 DSL lines out (2 Dialers) and 1 Fast Ethernet interface in with many sub-interfaces. The sub-interfaces represent the many companies that are inside this big building.... The second Dialer (Dialer2) is not being...

Hi, I am totally new to PIXes and need to erase/delete the running config from this Firewall with OS 7.1(1) I thought that "clear configure all" would do the trick but the command does not even appear listed when I do a "?" on the command prompt.... capture Capture inbound and outbound...

Hi, I was trying to do some work at home and it seems that I have messed up my home router... I loaded a configuration from a 2621XM into my home 2621 and now, when I try to establish a hyperterminal session all that I get are strange symbols like A#a+„R+! k++ *#")cý¤...

Hi, I am having the following problem with a Cisco Router.... I can ping the router from my office but cannot telnet it. This is, cannot telnet to the interface that connect to the Internet However, I can telnet the router on the interface that connects to tha LAN Any ideas why?? Enable...