Search results for query: *

Is there a way within the Manager to force a 9608G passthrough port to: Ethernet 1000Mbps full / PC Ethernet 1000Mbps full It appears to go to auto- negotiate or a slower speed having to enter the Mute <password> # / INT to set the speed manually at the set, I would rather force it is possible...

I have a 10.1 server edition: Added the HoldMusic.wav to the opt/ipoffice/system/primary directory as required through the embedded file manager. Tested and music played as expected. I want to replace that Music with new. I deleted the file with embedded file manager and loaded the new...

Often we run a Hub off the pass-through on a 9608 type set. Seems to work fine The question has been bought up - can we run multiple 9608's through 1 hub in cases where limited network drops are available? (obviously needing power since no POE is available) Thanks in advance.

I have been looking over bars and can not for the life of me understand why this call is not going out over the first choice: There are 2 routs in the RLI 1st choice to 112 (WAN rout - insert 9 to another site to go out Dedicated LD trunks) 2nd choice is oout TKNA Ground start trunks. Call to...

I have a 5.5 system with an SPN of 9-911 already built - Pretty standard... SPN 911 / RLI 0 - RLI has LTER The Emergency Services DN Primary is 911 / ESRT w.t misdial prevention. No ELINS If I want to insure they can also dial 911 Can I just Build SPN 11 - New RLI w/t DMI to insert 9 to the...

I was given the Patch p20913_1 for a 4.5 system that has the Memory issue... I have installed entire Deplists before but never a single pacth. What is the proper procedure?

Inbound # shows up preceeded by an "H" but no name shows: 4.5 CS1000M Have done a "Stare and Compare" to known working systems. Verifies correct Package equipped. Current Deplist installed. We use 5 dgt dialing / Calls rout through NRS Programming of Rout / DCH / Trunks & Station below...

5.o / Cs1000E CPPM Analog line (500 type) Go off hook you get Dial Tone every other time - but only Talk Battery the other half. Verified @ Block w/t butt set Have swapped CARDS and SLOTS Only Analog set in system DES CAFE TN 004 0 07 00 VIRTUAL TYPE 500 CDEN 4D CUST 0 ERL 00000 WRLS NO...

I have a 5.0 system that I recently updated the DEPLIST on. I have 3900 series set with CLS MTA the field techs use to check COT trunks with. Since the DEPLIST install he can login with the maint set and access 1 cot - but then then the phone locks up - I have to login to a tty terminal and...

I have a 4.0 TM and trying to open a DBA session that I had open previously. I am able to select the site from the drop down menu but when I "Connect Now" I get an error that reads "Failed to create object. Make sure object is entered in the system registry."

I am a Nortel guy, tying to work with an Avaya guy - I guess we will be doing more of that soon. SO here is my questions. I have 4 lines from the Avaya 8700 (Analog) 4 digit EXT's that also have a DID ringing on them. If I call from one 4 digit ext to another, the ring cycle is a normal ring...

The Inbound calls on this setup are are not recognized by the trunk card right away... It may be 3 ring cycles befor the card recognizes. Somtimes it recognizes imediatly. I noticed that the ring cycle from the 8700 analog is 2 short ring bust. Is there a setting on my end that I can make to...

Is there and easy way to copy the Cost field in the TM Telephone Billing Module (TBS) from one site to another? (Telephone config - Call dgt translations / Carrier pricing templates) I have Telephone Manager 3.10.28.41 I have 80 sites, and only 1 is build correctly - SO I am trying to save a...

I am using LD 88 to try and OUT all AUTHCODES REQ: OUT TYPE: AUT CUST: 0 SPWD: (I know what this one is) CODE: ALL SECR: ( I NEED THIS ONE....) I look in the Input / output guide and it refers to SECR as the "security password" - I thought that is what SPWD was? Anyway - I have tried the same...

OK - A long time back I started this thread: thread 798-1210588 Basically We have a PRI at a High School, I have a DID off that PRI at an Elementary School. The DID is directed to the other site via a CDP to the WAN rout looked at a NRS server. I have the EXT on the 500 set with FAXA...

I had to upgrade firmware on 3904 Someone unplugged phone during upgrade. I tried to SUS 32 FDLU but it does not seem to Suspend. I still get the OVL316 error. When I SUS 32 FDLU it tells me that " PSDL ABORT IS WORKING PLEASE WAIT !" But it has been like that for about 15 min now. Do I need...

SITE 1 I have an option 11 (5.0) with a PRI and Inbound Caller ID Name & number work GOOD for the entire block of DID's at that site. There is a WAN rt pushing a certian block of DID's to aother site through an NRS. SITE 2 option 11 mini (5.0) only gets caller id number ok but NO NAME. I...

We get a lot of the TRK156 errors. So as another thread suggested: I did LOVF in LD 36 Cust 0 Rt 0 I am trying to find out what the Meaning of the output is. (What exactly HOLD and RGFL indicates) TN 4 0 09 00: RGFL HOLD TN 4 0 09 01: RGFL HOLD TN 4 0 09 02: HOLD TN 4 0 09 03: RGFL HOLD TN 4 0...

1120 IP phone It already had the ip configuration information in it and I have another ip with same config. The firware wants to upgrade over and over on ths one. It tells me on boot up: F/W version 0624C1A then it wants to firmware upgrade: updating frmare to /u/fw/x24.fw and then the...

Just thinking about it....Since for must of us it happens this weekend. FWTM 3 2 1 2 BWTM 11 1 1 2 SDST ON Other infor from this thread as well.... http://www.tek-tips.com/viewthread.cfm?qid=1339348