Search results for query: *

Hi All, Has anybody come across thier array battery disabling for their Signaling Server's? We have HP DL380's G7 and I'm trying to see if there is a way to get the status of the batteries via the linux cli. I have tried a few commands but no luck. Thanks in advance Jeremy

Hi All, We are migrating off our PBX and over to CUCM. In doing so, I'm trying to test our Valcom overhead paging system using an FXS port. The FXS port is connected up to a Valcom 9940(station Level page adapter) converting the fxs dial tone to 600ohm connection to the 9 zone paging...

Hi All, I'm trying to test an snmp alarms on our new CUCM Cluster. I have everything setup correctly in CUCM and I try to use the snmp set command in CLI. It is complaining about the dash in snmpset -c <community string> -v2c. Any suggestions or idea why this is not working? Thanks Jeremy

Oops, I forgot to add the actual error message. Here it is: SRPT316 Internal communications message transmission failed. % (Transport: AFS; Subject: accountDB_BannerUpdate; Action: PUBLISHER; IP: 192.16 % 8.202.57; Reason: 11; Details: ) Thanks JW

Hi All, I started getting this message last Monday, it happened once and then again today. It only happens during midnight routines. The error is coming from an MGXP. I can see that its registered. I telneted to the MGXP and did a joinsecdomain anyway and ran mids again and recieved the...

Hi All, We are currently migrating off our Avaya System and onto Cisco UC System. I have never worked with SNMP. I'm getting ready to alarm a couple Clusters. We will be using V3 SNMP and sending SNMP/Traps to Solarwinds. I have double checked all my config more than once and I still cant...

Hi All, I have received fir0016 and 0017 at 7:15pm the last couple of nights. Performed tests on both the controller and network card, both passed. Any suggestions as to what might be causing this error messages? Its very odd that they occur the same time each night thus far. Thanks in Advance!

Hello All, Do I need to disable the System Monitor card(TTY Port) and pull it out to replace a blower motor? Thanks in advance.

Thank you both for the replies. I have found my answer. :)

We have a cs1000 7.6 system. Recently we have moved a lot of workers to 2050's. In doing so they were built on virtual loop 224 1. Can you segment out a virtual super loop?

Hi All, Last couple of nights I have recieved these errors. FIJI010 0 0 ALARM 00 - RECVS_FROM 00000001 % % FIJI007 % NEW STATE RING 0: NONE % RING 1: FULL % % FIJI010 0 0 ALARM 00 - RECVS_FROM 00000003 % % FIJI007 % NEW STATE RING 0: HALF % RING 1: HALF I...

Hi All, I have a question: We recently had one of our PBX's INI. Now I get this maintenance message, DA AML :: Info :: AML: 0 MAINT INDICATION TIME, that comes up. I checked AML 0 and it use to be used for the old vm system. See below for the print out. ld 48 LNK000 .stat aml 0 AML: 00...

All, I was looking in the MGC Card and couldn't find any obvious commands under the "help" menu. Can a trace route be performed on an MGC Card? Jeremy

Thank you for the information. I have one last question. To this point I have always build a primary and backup security servers with SS and EM. I plan on going with a member server, do I still deploy the EM portion of the applications? Thank you for your help. Jeremy

Hi KCFLHRC, We have SIP trunks to the site. My understanding is if the primary fails the backup should take over correct? I hear you about rebuilding the Primary. It's a pain I do have another question for you. When you build the backup under the security section it asks for the IP of the...

Hi All, We have a CS1000E site that has a Primary Security Server. We will be adding a Virtual DCH and sip trunks to this site. To give us redundancy we want to add a backup security server in case the primary goes down. Its been a while since I initially install this sig server. Are the...

Hi All, First of all has anybody used the NT2K40WA? If so, is there a power board that gets installed on the 2616D as well? If so, does anybody know the part number for the power board? We use to have a 2616D with a on-board NT2K40WA. Somewhere along the line the phone was removed and is...

All, Is there a setting on the PBX or CallPilot to mask/encrypt the password on your CLID of your phone when accessing your voice mailbox? Thanks Jeremy

I should have added that the CS1000E has MGC Cards and a CPPM for a processor. Also, we do have a CPDC Card for SS, but site doesn't have Voip sets.

All, We are moving a site from a location that has a cs1000E using the wall cabinet(old opt. 11c cabinets). I was curious if I could use the 1010 chassi's at the new site and just migrate the existing cards from the opt. 11C cabinets. If I can, is there programming changes that need to...