Search results for query: *

In nortel MICS we normally program 5 seconds for disconnect clear to solve this issue. but here i tried to do change with the option disconnect clear in line properties & busy tone detection in system telephont settings. but still the transfered calls are not disconnecting.

Hi i have a ipoffice version 1 with release 7. we have a problem with our analog trunk disconnection. when we transfer an external call from reception to other extension if the caller disconnects then also the extension get ringing. the trunk is also not disconnecting in case of this...

Hi i have a ipoffice version 1 with release 7. we have a problem with our analog trunk disconnection. when we transfer an external call from reception to other extension if the caller disconnects then also the extension get ringing. the trunk is also disconnecting in case of this transfered...

Hi I am using exchange 2003, I need to block 1 sender to sending mails to our domain. i tried in exchange-globalsettings-message delivery-properties -sender filtering. i added the email address i want to block. But still i am recieving from the same mail address. anything else we have to...

Hi I tried all the options in bcm & IPO. We tried with G450 instead of ipo with same ipo ip. and without changing the bcm settings. We can able to call both side. That means BCM settings are ok right.

Hi I tried with same codec g729 on bothe side and g711 on both side but the result is same

Hi I tried with both Qsig ng h450 But there is no result

Hi friends, Thank u very much for the reply. I tried all the options suggested . But Still

Yes That i did is same as per the doc. In THis same BCM 400 2 other BCM 400 are already tied using h323 and working fine. But in new branch they purchased ipoffice But we cannot dial from ipoffice even bcm extn. The pri came on 1 of the bcm400.

Hi At present numbering type of bcm is cdp We tried the Private numbering type of bcm tp UDP and None. But the no effect. I am getting the same result. What abt the licence in ipofice for the h323. i have 8 ip 500 voice networking channels is that ok for this tie right

Hi My short code for truk 8xx dial phonenumber . Truk group When i dial 810 its sending 810 using the 1st chnl but nothing showing in bcm monitor in avaya system monitor i am getting the error disconnect from destination end.

It sayinng the cause code 28 means Cause No. 28 - invalid number format (address incomplete). This cause indicates that the called party cannot be reached because the called party number is not in a valid format or is not complete. how we can solve this

Ok I tried that also but the same result. when i trace the call from system status. when i try to access the trunk its showing the following trace. When dialed using ars IP Address: 172.18.1.40 Line Number: 17 Number of Administered Channels: 8...

ticked only -allow direct media path out of band dtmf

The subnet mask is correct. Now i am pasting successful system monitor when i recieve a call from bcm extn 845.to my avaya extn 737 UNICODE-UTF8 eng ********** Warning: Logging to Screen Started ********** 4428853mS H245Rx: v=22 peb=17 userInput 4428853mS H245Rx: v=22...

The subnet mask is correct. Now i am pasting successful system monitor when i recieve a call from bcm extn 845.to my avaya extn 737 UNICODE-UTF8 eng ********** Warning: Logging to Screen Started ********** 4428853mS H245Rx: v=22 peb=17 userInput 4428853mS H245Rx: v=22...

I created new h323 line 17 with incoming and outgoing group id 100 Te1 8 and channels 8 outgoing chnls 8 vooice chnls 8 in the voip settings:gw ip -172.18.1.40(bcm) compresson-automatic supplimentary service-h450 call initiation timeout-4 ticked -allow direct media path out of band dtmf

Hi Also is there any diagonistic facility availble in system status to check the connectivity bw ipoffice phone and bcm phone. From bcm diagonistics i pinged successfully to ipoffice.

hi i hv i iproute like this in ipoffice. Also i can ping ipoffice from other side. IP Route Ip Address:0.0.0.0 IP Mask :0.0.0.0 Gateway:172.18.3.20 Destination:Lan1 Metric:0

Hi I tried to connect ipoffice and bcm 400. i have 8 network license in ipoffice and bcm hv 16 voip lines. now i can call from bcm to ipoffice. but from ipoffice to bcm is not working. ip details of bcm-172.18.1.40 ip details of ipoffice-172.18.3.40 pls find below the system monitor...