Search results for query: *

Hi guys I am a bit of a VoiP newbie so sorry if this sounds like a silly question. But the UC520 doesn't support SRST, so how do users make calls if the WAN link fails? Hopefully this is an easy answer! Thanks ---- Sunyasee

Hi I am quite new to HP switches, but I have worked with Cisco in the past. I just wondered if it is possible to setup a Qos/CoS policy to garantee a % of bandwidth for certain applications using HP switches. We have a scenario where a customer has a point-to-point 100 Mbps link between two...

Hi I have a network with two ISP connections. I want to use both links so that effectively I have a default route over both connections, I have an ASA and obviously it is not possible just to add in two default routes. Routerman suggested in an earlier thread that you can do this by setting...

Hi I am unable to get passive FTP to work through an ASA. Has anyone come accross this problem before and has a possible solution? Thanks ---- Sunyasee

Hi Bit of a strange question. I have an ASA that has connections to two different ISPs. There are about 10 remote sites that connect into it over VPN. What I want to do is connect one interface to ISP 1 and another to ISP 2. The idea is that some remote sites use ISP 1 interface address on...

Hi Can someone tell me the command to TFTP a config back onto a PIX. I have made a backup using the command 'write network' but am unable to work out the command to put the config back onto a PIX? Thanks for any help. ---- Sunyasee

Can you post your configs here so we can have a better understanding of what is happening? ---- Sunyasee

Post your config here. It sounds like you need to setup a static nat entry. ---- Sunyasee

Hi Antelope I used that example but was still unable to get it to work. In the end I used Nat on the PIXes to chnage the internal address and did the VPN p2p on the Internet routers. That was the only way I can get it to work! Thanks ---- Sunyasee

Has anyone ever configured a Pix to Pix VPN with overlapping networks? Is this possible? I have found examples of Pix to VPN Concentrator, but have not seen an example of Pix to Pix. I need the whole networks at each side to talk to each other. Any help would be gladly appreciated! Thanks...

Hi, I am trying to configure SDSL with BT and am having lots of problems!! They say that the line is fine and it must be a problem with the config on my Cisco router. Does anyone have a sample BT SDSL config that works that I can compare mine with? Thanks ---- Sunyasee

Hi Is there such a command on the PIX to enable split-tunneling for a PPTP client connection. I need the PPTP connection to have split tunneling. I know the command 'vpngroup XXX split-tunnel XXX'does this for IPSEC VPN clients. Thanks ---- Sunyasee

Hello I am trying to work out a solution to enable load balancing with a PIX that is connected to two routers that each have a 2mb connection to the same ISP. The idea is that the two routers are configured to load balance and give 4mb of bandwidth. Trouble is how do I configure the PIX to...

Hi, Thanks for the reply. Sorry meant to say I had downloaded drivers before installlation, not installed them! I uninstalled everything and started again. I got hold of the drivers for Win2000 and removed the Win98 drivers, as I worked out this was wrong too. The camera appears to install...

Hi, Hope someone out there can help! I am trying to install this camera on Win2000, I have downloaded the drivers and installed them, restarted my machine and then connected the camera. It trys to install but I get a message saying... 'Completing the Found New Hardware Wizard Sony DSC An...

Hi, I am trying to setup a VPN configuration from a Pix 515 to another VPN device. I receive the following error message.. crypto_isakmp_process_block:src:1xx.xxx.xxx.123, dest:2xx.xxx.xxx.125 spt:500 dpt:500 ISAKMP: phase 2 packet is a duplicate of a previous packet ISAKMP: resending last...

Hello! I am setting up a PIX with an internal network of 10.0.0.x with a DMZ network of 192.168.1.x. What I need to do is allow communications between a server in the DMZ and a server on the inside network, communication needs to work in both directions and needs to be restricted to just one...

Hi, I am trying to set up a VPN between a PIX to a 3com Firewall. The PIX Firewall is performing NAT so the network is numbered with a private IP address range. At the other end of the VPN link they have just public addresses and no nat is taking place. I was wondering how to setup the...

You dont need to apply the access-list to the group. The clients using pool group2 will get assigned a 10.1.0.x address, the access-list will permit or deny them access based on their source address and the destination address they are trying to reach. ---- Sunyasee

You could do something like this. In this example users using VPN group2 credentials only have access to 192.168.1.100 on port 25 SMTP. ip address inside 192.168.1.1 255.255.255.0 nat (inside) 0 access-list vpn access-list vpn permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0...