Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations biv343 on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. William C290

    Avaya SBCE for SIP Trunk & Workplace

    I need two host servers to implement, one for EMS and another for SBC, as deploying SBC+EMS is a basic mode.
  2. William C290

    Avaya SBCE for SIP Trunk & Workplace

    Thank you, do you mean small SBC just have 3 NIC, or when I installed it just have 3 NIC Connected. When deboyed the SBCE, I configure Six Port and assigned each to VLAN configured ( A1,B1,A2,B2,M1,M2) Actuallay, on the VM setting, I sawe just 4 network adapters connected, then I added 2...
  3. William C290

    Avaya SBCE for SIP Trunk & Workplace

    @derfloh: I check the NICs on the VMWare, first it's 5 NIC, and I add two and assigns to VLAN but, reset SBCE but nothing. About the option two, can you illustrate it as I don't understand it ? i try something like this but when start dignosteic test not working, what should I do on the VMWare...
  4. William C290

    Avaya SBCE for SIP Trunk & Workplace

    I will take your notes and follow up on the Avaya Document. But before this, I faced strange issues, after successfully configuring SIP Trunk, and moving to part two of configuring the remote worker workplace,' when trying to add A2 and B2, I couldn't add them ( not exist). for A2 there is no...
  5. William C290

    Avaya Contact Center Select 7.1.2.2 Ignotiation wizard configuration failed to complete

    Hi ... Is a Live IPO Mandatory to complete this process, because this is an upgrade from IPOCC to ACCS and there is a live call center working now, I have postponed the upgrade and programming on the exchange until this call center is completed. Because I see that even if this process is a...
  6. William C290

    Avaya Contact Center Select 7.1.2.2 Ignotiation wizard configuration failed to complete

    Hi ... I have completed installing ACCS 7.1.2.2, but when I start IW, the configuration fails to complete, as shown on the attached shared screen. I have also attached the log files as I don't know where the error occurred. Note that the deployment is on Hyper-V. Thanks
  7. William C290

    Convert j159 SIP to H.323

    H.323 J159 Not Supported on IPO. you can convert it, but this will cause problems when operating it.
  8. William C290

    Avaya SBCE for SIP Trunk & Workplace

    @derfloh: The Problem is that TLS many steps for certificates needed and TCP is easier to implement.
  9. William C290

    Avaya SBCE for SIP Trunk & Workplace

    Hello ... I have IPOSE 11.1.3, and SBCE for SIP Trunk & Workspace When the deployment of the IPOSE, I changed the TCP, UDP, and TLS ports under VOIP settings to 5090, and all the JSeries IP Phones now working using TCP Ports 5090 Now I need to Set up an SIP Trunk, and the provider uses port...
  10. William C290

    Avaya IPOSE - Alarm Emai Notification

    Hello, I have an IPOSE Rls 11.1, this morning the customer received the following email notification alarms: - SMTP: unexpected data received. An unexpected QUIT response was received. - SMTP: sending data failure. Failed in call to send message body. what does this error mean? is there a...
  11. William C290

    Avaya IPO Application Server 12.1 Deployed on Hyper-V - Additional HDD Isuue

    @derfloh : We tried that but unfortunately every time we try to run the machine, we get a black screen and the Linux installation is not complete.
  12. William C290

    Avaya IPO Application Server 12.1 Deployed on Hyper-V - Additional HDD Isuue

    Hello all, I have a problem, I try to install an Avaya Application Server12.1 on a Hyper-V Server from the ISO. I have 2 HDDs. 1-250 for Linux Operating System (sda), 2- 10000 for Media Manager (sdb) When I finish the installation and start the ignition Process, on the New Hardware page, the...
  13. William C290

    IPOSE - HTTP request failed

    @Akram1978: both ports opened .
  14. William C290

    IPOSE - HTTP request failed

    Hi @Akram1978 : Do you mean from security settings,
  15. William C290

    IPOSE - HTTP request failed

    Hello ... How do we solve this error when opening Manager?
  16. William C290

    IPO Rls 12.1 Latest Updates

    Hello @nnaarrnn: I follow this process from the Upgrade manual and the machine is VMWare. Page 107 What you suggest to use ???
  17. William C290

    IPO Rls 12.1 Latest Updates

    Upgrade IPOSE Rls 12.0 to Rls 12.1 on the VMWare Platform, is this using the same standard iso process, or there is additional steps that must to done before? For Media Manager should I stop the service before the upgrade or leave it? The main need for the Upgrade is to get rid of the...
  18. William C290

    IPO Rls 12.1 Latest Updates

    How to upgrade from Rls 12.0 to Rls 12.1 ( VMWare) ? Is using the same way ISO Transfer ? Because I start to day upload the iso image to the server but when they have 98% uploading the server stop working, when restarting it, the VM faild to start . What is the process to upgrade to Rls 12.1 ?
  19. William C290

    IPO Rls 12.1 Latest Updates

    Finally, Rls 12.1 is now Available on PLDS, and will soon be released on the support site.

Part and Inventory Search

Back
Top