Search results for query: *

Hi, I have this config on a cisco 881, but it is broken. I want to know if is it possible to re-create this config on a router Cisco 2621XM with 3 Ethernet interfaces : Current configuration : 5306 bytes ! ! Last configuration change at 14:24:25 EST Tue Dec 9 2014 by rene ! NVRAM config last...

Hi everyone, is it possible to setup at the same time, bridge mode in on antenna and access point for internal use on the other atenna ? Thanks

I found this information : ip nat inside source static v.v.v.v t.t.t.t route-map excludevpn ip nat outside source static t.t.t.t v.v.v.v ip access-list extended excludevpnfromnat deny ip s.s.s.s t.t.t.t permit ip s.s.s.s v.v.v.v route-map excludevpn permit 10 match ip address...

Hi everyone, I have a site to site vpn up and running. At one end I have a PBX for IP phone (SIP). All is working when we are inside (both side of the VPN). I can connect to my PBX and make phone call. But now, I have a client want to be able to connect to the PBX from outside. I said no...

Thanks for the answer, but I want more. I will check for a cheap router model. Bizz

Hi, I'm looking for to see if is possible to block the time per day each mac address can go on the internet ? I saw that some cheap router like Buffalo did, but I have a 2610 for principal router. Thanks

Another thing, My 2 IP adress will be on 1 DSL link. Thanks

On on IP, incoming connection to a computer inside and the other side network standard, Internet, mail and Interac System. The last one need to have some port open 2 or 3. Thanks

Hi, I will have an internet connection with 2 public IP with it. One will be Sattic and the other one will be dynamic. The static one will be connected on PC alone ant the dynamic one will shared internet for 5 PC. What kind on router that I need to do that ? Thanks

OK,thanks to all. I change my speed and duplex and it's work fine now. Thanks again Bizz

Hi, I have an issue with my 2924 XL. I try to broadcast movie trhough my home network and I have a lot of lag when I'm connected on my 2924XL. When I connect directly on my PC I have no lag at all. Even a realy big file. this is my config: version 12.0 no service pad service timestamps...

No one have an idea ?

Thanks for the reply, This installation is at Home. I share my internet with one of my neighbor. He said to me that he done a lot of emule and torrent. We working like that since 3 years without any problem. Until last week I was working with a Pix 506E. But he begin to lost internet...

I made the same test with a Cisco 2610 with ATM card. Same issue, after 15 minutes, the ping to the local interface of the 2610 have a lot of time out. Anyone have an Idea ? I saww the they handle more than 800 translation NAT at the time. Maby this the part of the problem ? Thanks in...

I ping the local IP address, in this case 192.168.2.1. The time is around 1 week. Thanks

Hi, I Have a Cisco 827 that is running fine for about 10 minutes. After this time I begin to have a ping timeout. I change my cable, change port in my switch and connected directly on my laptop, same issue. Thanks in advance. Here is my running config : Building configuration... Current...

I found my answer on the Cisco site. Here is my config workig. I can ping each other without any problem. Now I will try to setup my DSL for these two network. any suggestion ? I know my DSL informations. I use the BVI2 because with my DSL I need a BVI too and I want it on BVI1. it is my...

Hi, I have setup my Cisco 877W. But I cannot ping my LAN from my WLAN and WLAN from LAN. I post my config if anyone have an idea. Thanks in advance My config. version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec service...

I found my problem. The cable on the interface Ethernet 0 was bad. I put a new one and set the interface Ethernet 0 in duplex full. No collision at all. Thanks for everyone for your help on that issue. Bizz

OK, this is my setup now : Router 1605R Switch 2924XL-EN 1605R Ethernet 0 ------> 2924XL FastEthernet 0/5 1605R Ethernet 1 ------> ADSL modem PC Ethernet ------> 2924XL FastEthernet 0/4 Nothing else on that network. Still have a lot of colision. I don't have any control on the ADSL...