Search results for query: *

Hi All, I need help configuring an IPSec VPN. This is the first time that I try to do this via the CLI. I've done it with the SDM but I really would like to know how to make it work via the CLI. Below are the commands that I'm putting in but for some readon I just can't get it to work. I...

UPDATE: I was told by a co-worker that ACL(s) is all that would be required. Can someone please let me know what are the ACL(s) that I need to apply so that Site A and Site B do not access each other via the 172.25.10.0 network. Reason for all this: There is a server on the 172.25.10.0...

Hi All, I'm trying to configure a 2611XM to allow 2 VPN connections/tunnels for Site A and Site B. After the traffic for both sites get pass the edge router there is a 3550 switch that is L3 capable. I would like to have both sites establish a VPN connection to the edge router and be on their...

Unclerico, Thanks for your help. I forgot to request that I would also like to allow host 192.168.0.6 to RDP (3389) into the servers on the other VLANs. I assume that if I create more L3 VLANs, I just creat another ACL like the fist 2 (110 and 125) and then apply it to the SVI. Thank you!!! JR

Hi, Thanks for your reply/question. Yes, for now that is what I would like to do. Can you please assist me with this? Thanks!

Hi everyone, I configured (3) Layer 3 VLANs on a Cisco 3550 and would like to configure ACLs so that I can block traffic between them. This is what I have: VLAN10 SVI - 172.10.1.1 VLAN25 SVI - 172.25.10.1 VLAN163 SVI - 192.168.0.163 If possiable, I would like to allow host 192.168.0.6 to...

AWSOME!!!!! THANK YOU VERY MUCH!!!!!!!!!!

Hi All, Is there a way that I can pull a report that will list all the SMTP email addresses for all the users within our domain. I was able to pull a report within AD but it only gave me a list with all users and ONLY their primary email address. We have users within our domain that have...

We did the conversion and all went well. Thanks to you all for your time and help!!!

Hi, I would like to know what would be needed to have 2 domain names on 1 exchange server. We have users using company.com as the default email. We would like to add company.org as well but to be the default email address and the company.com as secondary. We created the company.org SMTP...

Guys, Thanks for all your help!! Eamil has been working well since Monday after our ISP put in the reverse DNS.. Thank you, JR

Guys, Thanks for the tips! This is a new exchange server. We just got the domain name last week. I do have Reverse DNS running and port 25 is only open for the email server. I'm still not sure how to create the SPF file. v=spf1 ip4:A.B.C.D a mx mx:exchange.domain.com include:ns.domain.com...

Hi All, We just put up an Exchage 2003 Server. We noticed that when we send an email to someone outside it goes into the Junk/SPAM folder. People using internet email like yahoo.com, will receive the email but in their spam folder. People using optonline.net will not get it because the...

Minue, I was able to get it to work!! Thank you very much for your help!!

Someone please help me as I need to get this up and running successfully by the end of the week. The sooner the better. Thanks in advance!!

Minue, I was playing around over the weekend trying to get this to work and had no luck. Should I just add the below via the CLI? SMTP: ip nat inside source static tcp 10.5.1.25 25 A.B.C.D 25 extendable Outlook Web Access: ip nat inside source static tcp 10.5.1.25 80 A.B.C.D 80 extendable...

Ok, Understood. So I should do this under the NAT section not the Firewall and ACL section? The direction should be from outside to insde, correct? Thanks!

Minue, Thanks for your reply. Below is the current running config of te router. If what I'm looking to do can be done via the CLI, please help me with the command(s) that should be added. FWRTR#sh run Building configuration... Current configuration : 9502 bytes ! ! Last configuration change...

Hi All, I configured a 2600XM as a firewall router using the SDM GUI. I would like to know how can I permit our new email server to send and receive emails, by allowing SMTP traffic using the SDM GUI tool. Thanks in advance!

No dice. It's like whatever I try, does not work. I'm confused...