Search results for query: *

https://drive.google.com/file/d/1m4Kaxh1cJd92wPkQOoEHq-KGNSq5aPEU/view

1. ROAPI:ROU=XX,PRITON=5,PREPRI=040687; 2. NUTRI

The current BC13 license file is valid for any version of SP0-SP8.

I did not save the INL_st_tsw_sp08_r9b version as unnecessary. In the EX version, the r9b correction was absent in principle. The license file during installation is placed in the /SYSN/USR1/SES/LI/ directory. If it is not there, then you can try to request a license file (its copy) from the...

I unfortunately only have SP8 versions of the two regional versions EX and ST. The rest were not interesting to me and I did not save them.

In that case, I'd rather pick up a 12 LIM station from INL. This will get rid of all current problems and upgrade to TSW sp8.

In order to carry out data correction by the SACOS command, it is necessary to have a thorough knowledge of the data storage structure in the station. Without this data, it is better not to use these commands.

I will express my opinion on the topic. A couple of times there were similar problems with the station when the station responded with COMMAND LOST. Both cases occurred after incorrect deletion of data or hardware. In this case, it is not possible to solve the problem by restarting the program...

Good afternoon. You have a difficult situation with equipment that no one will solve remotely. Most likely, you will need to save all the data and then install the station with INL. This requires a personal presence at the facility. Look for a specialist in your area. Or study the documentation...

VERSION: CXP1010139/4/TSW-SP08/R9A 11 LIM There was a problem with a dump of the station. LIM5 tried to reboot. Did RFEXI. Nothing helped. Tested LIM and GSM according to ALEX. Nothing is revealed. There are thoughts about it? <dusyi; SYSTEM DUMP INFORMATION NO VALID RELOAD DIRECTORY EXISTS...

The provided scheme of a cable for connection via the special adapter is higher. At direct connection won't work. Here scheme of a direct correct cable. NIU-COM B02 - 2 A02 - 3 B08, C08 - 1 A08 - 7, 8 С06 - 4 B06 - 6 A04, B04, C04 - 5

I checked in addition similar behavior on IPLU H.323 route. Return of a call on IP a route also began to take place normally.

I have absolutely forgotten to add. Testing is held on: VERSION: CXP1010139/4/TSW-SP08/R9A

Dear colleagues. I work with the equipment of this producer long ago and is not so naive that having adjusted a route, to register one timeslot and to demand from TSW of return of a challenge without having free resources. It is natural that E1 with CISCO is registered completely. As above I...

fcpli In a stream with CISCO of 18 timeslots and 17 of them free. <roedp:rou=5,tru=all; ROUTE EQUIPMENT DATA ROU TRU EQU IP ADDRESS SQU INDDAT CNTRL 5 001-1 001-2-20-01 H'000000000000 5 001-2 001-2-20-02...

Why you consider that TSW tries to occupy already occupied channel. In a stream of E1 30 timeslots and 29 of them we are free. What prevents TSW to occupy any free timeslot and to send a call back on initial PBX to the vacant room?

Your right not to trust me, but CISCO has nothing here. Especially for you trace of a similar call of Alcatel-Lucent OmniPCX Enterprise - TSW - Alcatel-Lucent OmniPCX Enterprise is given below Apparently the situation is similar above given with CISCO. >>>> Incoming Message: SETUP Call...

At the very beginning of the first message I did mentioning that CISCO in this case is taken for convenience of carrying out a test call. Precisely the same behavior of TSW is watched also in case of communication with other PBX for example of Alcatel-Lucent OmniPCX Enterprise or LG CS of 1000...

I understand that developers consciously locked the call routing situation provided by me. The question was in opportunities standard means of TSW or way of program corrections to make available similar routing. Repeated loopback of passing in my case will not be as on TSW there will take place...

This message is given by the station. Nobody asks to occupy already involved timeslot. There are 29 more free. What is interesting. If to create two routes of ROU=5 and ROU=7 to divide between them stream timeslots in half, then the station having accepted a call on ROU=5 sends him on ROU=7...