Search results for query: *

Have you issues command "ip routing" ? if not you will not not route You will also have to make sure the "connecting" network exists on both of your L3 devices...

It sounds like you have a corrupted boot image. You have to recover. The process sucks. There is a document out there on it. I would type out how to do it, but its too long and too many little things to watch for. Find the recovery document or call support. Sorry.

You can try NRS (Network Resource Solutions) www.nrssolutions.com As for Tom Tormey, he has helped us out a lot. 801.705.8999

Thats what it sounds like to me... No boot image

Hello, My department is trying to multicast some MPEGs and the like but for some reason cannot connect to the server. Does anyone know if there are any settings that I need to change for this to happen?? I am new to the video multicasting stuff, but I can also say that we can use a hub...

I am trying to find a rogue MAC that keeps popping up on my network. Becasue of the way I have my IP structure network segmented it will tell me the building and floor of the MAC. If, that is, I can get my switches to record or notifiy me of its existance when it is inserted. Thanks J

I hope we dont have that many issues... we just got in 2 3120s and 57 1001s I have to get config for 3 channelized DS3's... 1 thing I can say is that the 1001's get HOT bad air flow design.

Hey all, Is there a way to get a switch(8600 or 5530) to log or record when a rogue IP or Mac shows up?? Thanks J

You don't need to configure the MAC offset, the system will assign them in order as you build the configuration " This does not seem to be the case for the 5500 series. Everytime I created a vlan and assign it an IP I was required to enter a MAC Offset value.

Thanks for the info!!

Stamp results: Image: rel/14.00/ Created: Tue Dec 7 01:00:37 EST 1999 And we dont have support on this so I cannot upgrade :( Files in flash: File Name Size Date Day Time -------------------------------------------------------- ti.cfg 132...

I have some SHOW commands where I get the error run: File t1.bat show not found. run: Error at line 100 in file 1:show.bat Any ideas on how to fix? Also, how do I console into a BCN, I see a serial interface the SRML module but that is all?? Thanks!! J

One way to do it is if you know where its connecting to on the other end. Say its an 8610 or something like that, then you can Use Device Manager - IP - ARP tab. This will show you what IP's and MAC's are on each port. You may want to ping the subnet its one, if you can find that.. that way...

Hello all, I am getting A LOT of the following errors, any hints?? 43: [08/22/2005 07:04:59] WARNING Task=tCppRxTask squid3_pioRx: Squid has been reset. SquidResetEven 21 & 11: [05/16/2005 04:26:14] WARNING Task=tCppRxTask Frame buffer utilization has exceeded 90% threshold I am getting...

Thanks! FYI I had to remove BOOTP from my interface and re-add it to get it back???

Nortel is not cutting it... Please help. Logical layout: DHCP server-BCN-ISDN-ARN-Client I have an ARN at remote site and I need to setup DHCP forwarding so that my client can get DHCP. I was told it is my version, but this router was in the field at another location working just fine not to...

Please disregard... I figured it out.

Ok, on an 8600 the command is save config standby 1:config I cannot get it to work on a 1200?? Anyone help me out on this? Thanks, Omega

The get to the command line you will type BCC at the prompt.. and wait, then type Config. You are now in config mode can configure the router Site Manager you will install, run and click connection and add the ARN's IP and SNMP community names. Once connection is established click on TOOLS >...

Okay... my memory is shot. I have done this before but I cannot remember how to assign SPID's an AN/ARN router. Can someone refresh me PLEASE for for I go crazy. Thanks, Omeaga