Search results for query: *

Thank you Slash50. I will give it a further push this side. But let me know if any idea crosses your path. Direct inward dialling (DID) may be another crude way of linking the BC12 to any of the BC7 but it is not the ultimate because one has to dial a code (say 01) then dial the desired...

Thank you Slash50, I am in Africa and the PBXs are BC12 and two BC7 (old indeed). I no longer have issues with the two BC7 as they can now see each other via TLU76. The challenge now is how the BC12 can talk to them (two BC7). The connections are all through Ericsson mini-link radio 4E1s. Can...

Satellite1900 Thank you for the prompt response, but can you please expantiate your post? Is that all I need? .

I am at a verge of tying three of my Office MD110 PBX but just discovered that I need a licence for the BC12 to be able to integrate the other PBX via TLU 76 board (QSIG ISDN). Where can I get the license and how much will it cost?

Lalrl, Thanks, but can u explain further or rather diagramatically because the GJLU4 connector RNV 304012 has about 10 pins. i.e 2 pins in the middle row and 4 each the other rows.

Hi, I have just replaced my old 2mbps UHF radio (between two LIMs) with a new airmux-200 + 2E1 radio. The interface is now from the RJ45 E1 port on the airmux to GJUL4 card on MD110. I am confused about the Rx and Tx pinout on the GJUL4 board using twisted pair cable. Can someboy please give...

Thanks parnum. What about the first issue?

I have two major issues at hand: Issue I I want to connect 3 of my MD 110 remote LIMs. 2 of the LIMs are of thesame version (BC 7) while the other one is BC 12. I am planning to use AIRMUX 200 Radio with E1 connection. The issues I want to find out are as follows: a. Will the group switch...

Ok Mundus, pls send me the pin out so that I can make a fresh cable.

The coax cable Iam using still passes through the PCM equipment but NOT through the faulty radio itself. Does GJLU4 to GJLU4 connetion between 2 LIMs require any special cable? Mundus,Thanks. I have tried the LPU board from the main LIM and it is still the same code 2300

whosrdaddy , I have tried option 2 as sugested but I am still having problem of GJUL4 to GJUL4 connection between the 2 LIMs. The remote LIM is not seeing the master LIM. code 2300 on my LPU display. I am using the coax cable from the faulty radio. Pls advice further.

Hi gentlemen, I have this big problem of link cut-off between two LIMs (MD110 BC 8) which were initially connected by2mbp/s radio through group switch. The remote LIM (160 extensions) loads from the main LIM (320 extensions), but now that the radio link is down, the remote LIM went off due to...

I urgently need to communicate with my MD110 but I misplaced my cable (PC to IPU).I now want to quickly make my own cable. Can someone please give me the pin out on IPU board, DB9 & DB25 connectors? and If possible with USB option.

What is the specification?

After the upgrade to say BC11 or 12, what other hardwares do I need?

I want to add 2 more LIMs to my existing PABX network but will prefer a change in the existing radio system. The new locations are 3Km and 30Km away from the master LIM. What I have in place is 2Mbit ARE UHF radio which is getting obsolete. Kindly tell me any Microwave radio (E1)that will suit...

Pin out for IPU and LPU cards needed.

I have checked but could nnot find the wiring diagram I need. Pls advice

Someone should please list out all the cards and their variuos functions obtained in MD110 BC 8 and later versions. I am a beginner with less than 6 months experience on MD110 PABX but I like the job and have keen interest. Suggest also any site that can be of importance to someone of my level.