Search results for query: *

Hi thx for answer. I reat that it is possible ti increase the timeout for spific connections about modular policy framework. do you have experiences with M P F ?

Ping is not TCP.....i think this is not a solution but Thx. I need a feature to set tcp sessions with special content to keep it in for 8 ours

Hi all, my customer is using an old application without keep alive feature. The protocol is TCP 9999 and it is use one central destination Server-IP. The Problem with ASA 5580: If an user is creat a session to the server and no datas will be sent for next 10 min, the session is auto closed...

Hi @ all, my Catalyst 3750E logs frequently the message bellow: %SFF8472-5-THRESHOLD_VIOLATION: Te1/0/1: Temperature high warning; Operating value: 30.1 C, Threshold value: 0.0 C. The joke is that the threshold value is 0.0 C. On other switches i did´nt get these message on Te Ports...

Hi thanks a lot for your comment. Can you describe the change please. What action will effect after the reconfigure from informational to critical. Is there any white paper on cisco site????

I try to configure the logging about the ASDM. I using a logserver to record the logs in the network. Example for rules: access-list KV-XXX_access_in extended permit udp object-group LXXX_WAN-ADD any eq ntp log disable access-list KV-XXX_access_in extended deny ip any any log critical...

Hi All, i dont understand the ASA-Logging Feature. I disable the logging feasture on any firewall rule but the logging runs futher with all kinds of messages. I want to log only the deny rules on my policy and not more of these. Is it possible? i think i need an explanation of this logging...

Hi i have one upling (1x Po-Channel) from 3750E to Routed Core Layer. Any idea?????

Hi my access layer with Catalysts 3750E switches execeeds the limit of 128 PVST STP instances. (140 Vlans in use now) Now i would to reconfigure my Spanning-Tree from PVST to MST. Question: to save further other vlans agains loops and co, is it possible to configure more than 128 MST-Groups...

Thank you for your answer.

Hi, is it possible to configure more than one vtp domains in the same core-sw? (Cat 6509) Maybe with a new IOS and new hardware? It would be great to configure 2 vtp domains on the same device. I need this as security feature. THX

Hi, it sounds like a ProxyArp effect in Vlan 255. Do you have other Routers in this VLan? y have, check the ProxyArp and ICMPRedirect settings on it (best is disable of this. Maybe you should sniff the traffic wo see the behavior and waht happends with the ACK-Pakets from v255. Hope it helps.

Hi all, is the ASA500series able to work (featureset) with proxysets? Im looking for a firewall with proxyfeatures for manual proxyport definition. (Proxy for HTTP, Telnet , FTP etc). When not...who can make suggestions for other kind of products. THX

Hi all, follow topology in attachment. The Vlan 1 is build with unmanaged switches. (this means no spanning-tree is possible). If in V1 a loop is produce, the managed switch and the router get an high utilization. This means the other network vlan 20 cant work too about the router in direction...

The configuration is right. The problem was the Mgmt-sys

Hi @ all, I tried to configure SNMPv3 on a Cisco Router with SNMPv3 auth. (Image is correct with k9) Config: snmp-server group admingroup v3 auth read test snmp-server user admin v3 auth md5 test This debug output is displayed on the Router after a request from Mgmt-System...

Hi, i think this is normaly. The Mgmt port is a 100 Mbit single port and can not be reach of routing form other zones. You can configure an IP on it to work with NSM or web only. On our ISG 2000 its the same. Mgmt-Zone (predefined ) is member in Trust-vr too. grettzz

HI @ all, is it possible to create a class-map for Bandwidth management on cat3750? i want to configure the follow: PC1 and PC2 (10.1.1.1 and 2) on SW1 should get 100% bandwidth traffic from switchport if they connect a destination (2.2.2.2) BUT If PC1 and PC2 (10.1.1.1 and 2)connect to...

HI, i have some probs bto understand the ASA-System I configured 2 Zones: Zone A (incoming) SecurityLevel with 100% Zone B (incoming) SecurityLevel with 50% If i establish a connection from ZoneA to ZoneB, the ASA will not take a look in the own Policytabel cause the Zone A with 100% is...

Hi, i think the easiest way would be to include the new asa in the cluster with only cluster configuration and interface ips. Then save the master cluster (backup will be save the config too).