Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by skinnypuppy56

  1. skinnypuppy56

    Cxi Controller

    I want to create mailboxes outside of what is created now 1-8 which are menu node and I want to create different ones. My issue is that we were 3 digit extensions before and they began with 1 and now we are 5 digits beginning with 2**** and in the controller anyone pushes 1 it directly dials...
  2. skinnypuppy56

    ATA Adapter programming

    I have a Linksys SPA2102 adapter hooked to an EnGenius base. I really cant get these 2 to talk . I have the EnGenius setup and registered to devices. Extension 20197 is setup as an 5010 IP device and Generic SIP phone with no luck, i reserved device MAC to assign an IP but can't access via web...
  3. skinnypuppy56

    IP Paging

    yes we connect to a bogen amplifier in most cases and external speakers.
  4. skinnypuppy56

    IP Paging

    I have setup a few 5485 paging units and notice that ringback will come through speaker then the announcement - can i get around this? MCD 3300 extension 20170 speedcall 0993 number *3720170 I tied with a # and no luck Thanks.
  5. skinnypuppy56

    XNET networking -voice quality

    We have several IP paging units ON 3300 controller and wondered how can i stop the ringback <THROUGH SPEAKER> before paging announcement - pretty annoying. we set the paging unit up with extension user and device 5010 IP Set a speed call 0993 with dial string *3721070 I tried the pause # and...
  6. skinnypuppy56

    G729 G.729 G 729, AT&T is stating a new SIP reqmt for G729

    We have a similar setup but we have a lot of simultaneous calls so we went with G729 out of the gate to help reduce bandwidth issues due to inbound call volume. i thought you could tell carrier to deliver G729 and set the SIP peer profile the same. i know if u put call on hold or vmail it would...
  7. skinnypuppy56

    Resiliency handoff

    do the phones stay in resilient mode <blinking cursor> or does phone loop trying to reach ICP?
  8. skinnypuppy56

    Calling All Mitel 3300 controller experts

    Please read below,we are currently engaged with Mitel/3rd party vendor but looking to the tek-tips community for further assistance/ideas. I the customer am currently experiencing issues with resiliency and fail-over in the Mitel controller world. The basics are we were sold on (2) controllers...
  9. skinnypuppy56

    iSNS Server

    Just completed setting SAN up. We have a HP 2312i and now trying to determine why/how to use the iSNS server for the discovery of storage? 2008 Server Domain Controller is what I imagine I will use as server I have the version 3.0 downloaded for install
  10. skinnypuppy56

    SIP peer timeout

    Has anyone come across this? I believe it's at the Carrier Level .I called Mitel and they have nothing. The SIP peer profile is set at 330 which I imagine is default.
  11. skinnypuppy56

    Codec on SIP trunk calls

    in my discussions on this topic it comes from carrier adnd stays compressed in the mitel but very important that voice carrier has it at G729
  12. skinnypuppy56

    HP SAN 2312i

    nice, i did finally realize this after going through setup, however now I'm stuck on iSNS server setup and each volume on vdisk is on controller A. I left setting on auto for that but did not split it up over A/B controllers.
  13. skinnypuppy56

    Reset a Phone

    ok, thanks. re-read and tried again. it did reset phone, pretty quick but worked - thanks
  14. skinnypuppy56

    HP SAN 2312i

    So we purchased a iscsi san and we want to determine 100% that the iscsi port are that or truly ethernet ports? We know it has mgmt ports per controller but we are puzzled? Thanks, John
  15. skinnypuppy56

    Reset a Phone

    I tried this and window jsut shows load initiated after I confirmed the command? No phone reboot? laod ipdev xxx <xxx=extension> and zip? I have the 3300ICP 4.1 sp1 SOFTWARE 10.1.1.11_2

Part and Inventory Search

Back
Top