Recent content by PinkeyNBrain

Can you open a window (sub window / top level?) that has a generic "OK" button and that button is given focus so that all the user has to do is hit return?

If lsort supplies the end result you need and you are not constrained by time issues of lists that are 100's of thousands long, then go with it. If you have huge lists and sorting speed is paramount, there are sites where you can find/review the various theories/algorithms on sorting. Bubble...

Bit of a swag here, but do you needdashboard_set_property ${::led_control::dash_path} box_led_${led} onChange ${::led_control::toggle ${led}} .. add a $ var ref to the last parameter? Try addding a "put 'xxx'" command inline and see if that parses out to the variable value you're after.

Give this a try. It's totally brute force, but for the sake of getting a job done over elegance -- # # Reading in # undef %org_data ; $line_num = 0 ; $char_count = 0 ; while ($inline = <DATA>) { $line_str = substr('00000' . ++$line_num, -5) ; chomp $inline ; # ?? Does your 'at char...

Skip - Thank you for your time. My attempt at a colloquial explanation of what I’m doing, versus demonstrating thru code, has fostered a completely wrong picture of what I’m doing. In this case a 'table' for me is roughly a grid 3x10 in size. The entire screen has columns A-0 (15 columns) and...

MOVE = CUT – Got it. Your usage of caps caused me to think you were referring to another command. Usually I see people asking for code more over than concepts - but here goes: - User enters data into a textbox on a worksheet (not a cell but an activeX object). Hits enter. - Sheet level...

Indirectly tried the saved address idea. ConsiderSelect Case some_val Case 1: Set cell_ref = default_range1 ' Assume this is selected Case 2: Set cell_ref = default_range2 End Select save_addr = cell_ref.Address cell_ref.Cut Destination:=cell_ref.offset(1,1) set cell_ref =...

Problem: I want to move a range of data but using code similar to[CODE VBA]src_range.Cut Destination:=des_range[/CODE] I find src_range.Address is changed to match des_range.Address. In some cases my value for des_range is compromized. I want to retain the original definition of...

Sure - thx

Please substitute Destination for Destionation above

Problem: I want to move a range of data but using code similar tosrc_range.Cut Destionation:=des_rangeI find src_range.Address is changed to match des_range.Address. In some cases my value for des_range is compromized. I want to retain the original definition of src_range.Address. I...

This is a tad brute force, but will get you thereprint "cc>$cc<\n" ; print "container>$container<\n" ; print "h_set'component'>$h_set{"component"}{$cc}{$container}<\n"; prnit "\$_>$_<\n"; ; print "h_set'interface'>$h_set{"interface"}{$cc}{$container}<\n"; print...

Thinking back, I have seen that sort of thing before - the system call executes under a different set of credentials. At a command prompt I tried 'help start' and 'help cmd' and neither of them showed references on how to supply a user/password in the calling sequence to potentially reset your...

Taking a swag here ... Does$cmd = "d:\\\\officetopdf\\\\officetopdf.exe /print"; work? (Using 4 backslashes) Try dumping $@, $! and $^E as well. May give more insight.

Couple thoughts: 1 - Your assignment $cmd = "d:\\xxx\\yyy" ; Will translate into d:\xxx\yyy in $cmd. Then when you use `$cmd` it is looking at d:\xxx\yyy and will again translate the \x and \y into their equivalent escape characters. Try using single quotes on the initial $cmd = 'd:\\xxx\\yyy'...