Recent content by lecarbajal

Hi, Im trying to configure a policy nat for traffic coming from a VPNL2L. I would like to know if this scenario is supported on a Cisco ASA IOS version 9.1(2) We have a VPN L2L for different customers, one of them has an overlaping with our internal network, we need to nat a specific...

Hello The issue is that is not UP during that time, we change our old FW for a new one Regards,

I have a problem trying to connect a VPN site to site between a FWASA 5515X - ASA5510 this is the configuratiof of my 5515X hostname FW5515X-1 domain-name cngfinancial.com enable password yjBYwn.g8xmd24FA encrypted passwd 2KFQnbNIdI.2KYOU encrypted interface GigabitEthernet0/0 shutdown...

Hello, I already manage to fix the configuration in order to allow the traffic from the HP to the core switch. thank you for your advice.

Hello, i tried to configured the connectino between the HP and the Cisco like trunk like this exit vlan 1 name "ManagementVlan" untagged 1,5-28 ip address 10.10.1.100 255.255.255.0 no untagged 2-4 exit vlan 6 name "Phone3rdOffice" untagged 2-4 ip address 10.10.4.10...

thank you for your reply, i already configured the ip routing in the cisco switch. vlan 6 description datauser ip address 10.10.4.1 255.255.255.0 the port configuration its like this: inter giga 1/0/37 switchport mode access switchport access vlan 6 I only use the port as a access in the...

Hello, Hello i configured a sw 2620 as an acces switch I defined 1 vlan in order to connect phones there, i already integrate with my Cisco Switch 3750X, my only issue with the HP is that i can not ping to the VLAN IP even its connected some equipments to the switch, i attached the...

Hello, I would like to know how to configure a router 2900 to support connection from 2 firewall ( Active Standby connections) How can i said the router to send the traffic to the stand by when it go down the active Firewall? I was planning to use a Switch ( layer 2 capacity only) in the...

Hello, I having a problem trying to connect a Juniper SGS5 by ADSL to a Juniper ISG1000, This is the scenario: the SGS5 use a ADSL line to connect to the ISG ( WAN Public IP), i use ddns in the sgs5 for the wan i setup all the values and in the ISG also setup the psk, the route , for this...

Hello, I have one issue related to the remote access, I would like to setup two source for the remote access account at the moment i have setup against to LDAP but i would like to setup a second one directly in the local database of the FW in case the LDAP fail, is it possible this kind of...

Hello, i have and issue related to the management account I login to the firewall using a TACACs+ account as primary and if it fail i use local account. I would like to manage 2 local account for administration purpose but when I use the second local account i can not login even i apply the...

Hello, Is there a tool for convert the configuration from a cisco ASA Firewall 8.2(1) or 8.2(2) to 8.4 ? Regards,

Hello, is there a software to find changes in the last configuration of cisco's equipmenet in order to find mistakes ?

Hello, I would like to know how many DHCP domain and range can be configured in a router cisco with an IOS that support a basic DHCP configuration?

Hello, Is there a command to reset the HSRP group in a cisco 6509? My problem is : I have 2 swcore 6509 configured with HSRP + PVST some groups are active in one switch and the others are active in the secondary switch. After a maintenance we had a problem with some border sw connected to...