Recent content by hooktom

But I think this is not a defect In normal mode, the ability to connect by pressing the first digit of the telephone line is pleasant for the subscriber. The hotline also has a special function and works as we want (start dialing immediately after picking up the phone) But the problem with their...

hi REG-COP:8; H500: AMO COP STARTED ADD-COP:8,DTMF&EOD&SFRM&RLSB&RLSA&BR64&TDED&NO1A&DITW&TIM1&NSDL&IDP2&DTM1,,,,; CHANGE-COP:8,COPADD,,,,INDEP,"TMANI";

ADD-LDPLN:LCRPATT,0,"99"-"X",0,20,,,1,,,,N; {of course I tested with these LDPLN but the same problem exists: ADD-LDPLN:LCRPATT,0,"99"-"Z",0,20,,,1,,,,N; ADD-LDPLN:LCRPATT,0,"99"-"XXXXXXXX",0,20,,,1,,,,N; }...

My system is 4k and phone work in HFA mode

Hi guys I have a user with a phone (IP 35G) and I want to send every digit that this subscriber dials directly to an analog trunk (without dialing the prefix). I have currently assigned a prefix to use the analog trunk and using the hotline, immediately after off hook the phone, the prefix is...

I searched and read ptime related issues on the forum based on your answer - and then I realized that the (P) parameters were probably related to my problem. I started with the P6 parameter and reduced its value (75--65--50).when i set it to 50 - the result was acceptable and all calls were OK...

Thank you very much Moriendi My problem is solved I had used table number 5 in circidx and by changing the P6 from 97 to 50 in this table ,my problem was solved.

hi Moriendi i test it by SLMA .But no digit sent .

I will definitely do that test tomorrow and send the results. I sent DIS-PTIME. Results. Is your request something else? REG-PTIME; H500: AMO PTIME STARTED CHANGE-PTIME:SLMA,1000,4000,300,400,300,4000,1000,1000,300,400,300,1000,500,200, 200,200,200,200,4000,40,110,200,100,1000,600...

AND DIS-PTIME:REST; H500: AMO PTIME STARTED REST TIMERS: ============= INIBLOCK: 104 DEVICE: EMCONT2 TBLK: 0 ----------------------------------------------------------------...

Hi Moriendi and thank you for your response. for the first test, I haven't done it with the SLMA card , but I have several analog trunks whit the ISDN that work correctly with the same settings - that is, the digits are sent correctly and are also received correctly by ISDN...

Hi I used an analog trunk to connect Siemens v7 (hicom) and Alcatel (oxe ) by connecting an analog port from oxe to a trunk port from hicom. In hicom co trunk board (tmani ) ==========co trunk==============> oxe analog board (sli-16-2) Now incoming calls from alcatel is ok ,but some...

Hi sbcsu, My problem has been resolved. thanks a-lot for your reply

hi We have two hipath4k v.7 We want a group of subscribers with an access code (e.g. 99-x) has the outgoing call from an analogue trunk. Also, the outgoing calls from group 2 will be out by the same access code(e.g. 99-x) from another channel These two subscriber groups should have internal...

hello thanks a lot for reply I've tried to config my STMI with a client sip-compatible function block   But the result was that with the first setup, 30 licenses were used. And after that, I was able to add 29 other subscribers as subsets. Of course, the problem was not just licensing. The...