Recent content by dickinsonsfan

Yes... If i call in the CS1k i can make the transf. but if i call from CS1K and take the VoIP route i can't make the transf and conf. Regards. Rodrigo Ribeiro Oblesrczuk.

So that configuration is on the BCM isn't it? Regards. Rodrigo Ribeiro Oblesrczuk.

Hi... Sorry i forget a detail. If i use the BCM i can make the transf. and Conf. If i use the CS1k too i can make the transf. and conf. But if i took a telephone register on CS1k, use the VoIP trunk to call using the BCM i can't use this feature... Thanks. Rodrigo Ribeiro Oblesrczuk.

Hi everybody, i have a problem when i take the telephone and try to make a transf. from the CS1k to BCM, i can't finish the transf. When i make a call using only the nunmber and the NET_DATA the transf. is work. But when i take the VoIP route to call using the BCM, is like the BCM don't respect...

Hello everybody, I set the parameters T.38 on fax transport on IP trunks but the fax don´t send. When i put on G.711 i can listen a short fax signal, but with T.38 i don´t listen nothing. In CS 1k is normal but in BCM i only set on the IP Trunk the T.38 on fax transport. But is strange because...

Okay... Thank you... It's Work.... Rodrigo Ribeiro Oblesrczuk.

Hello everybody, Guys here i have a CS1k and a BCM, on CS1k i put a ac1 (0) to dial in Rio and ac2 (9) to dial in São Paulo, the BCM is here in São Paulo, my question is... I can make this on BCM? Dial the 0 to go to Rio and 9 to go to São Paulo? In Rio is working properly, but in BCM, i can...

Hello everybody... I have a problem in meridian when i use the stat (loop) on ld 60 one channel is locked, if i disable the channel and after enable this channel return locked. Is very strage... Have you ever seen this before? Rodrigo Ribeiro Oblesrczuk.

Soooo one more question about the SRG. What i need to do on the CS 1k? Need to program something? Thanks. Rodrigo Ribeiro Oblesrczuk.

Danshee, We must have a ATA to analog ring? So i see on documentation that need but i don't know why, this analog ring without one... So this ATA is important? Rodrigo Ribeiro Oblesrczuk.

Sooo in that part is right and on CS 1K What i need to do? I create a CDP on CS 1K with the DN number. I see on the log, when a call came from the PSTN the BCM only direct the call to CS 1K on the Main Office, but when the call came to the analog here, the call lost in the middle and go to DN...

Hi Dasheen thanks, So on the Priv. Oli i put the same number DN 300 on the Pub. Oli i put DN 300 too. If i use the local mode i can call DN 300 and i can use the telephone with no problem, but and i'm not in local mode i can't call, appears a H300 on the recepcionist telephone. Thanks. Rodrigo...

Hi all... So i have a problem here, with the BCM i have the 1230 in the desk but i can't call the analog on the CPD, but if i change to local mode on the telephone, it work! I dont't know sometimes i change something on BCM that is not important and start to work. Yesterday before i go lunch the...

Hi everybody I make the Board.ini. and change the file to .txt, what's the params that you want me to put here the file is large... Thanks... Rodrigo Ribeiro Oblesrczuk.

I take the board.ini and i change the extension to .txt to read the file, what's the config you want, because the file is huge... Thanks... Rodrigo Ribeiro Oblesrczuk.