Recent content by DEIVIDOS

hi, anybody knows a problem with park a call on mxone with the h323 telephones. i have probed with SIP terminals and all works fine. Thanks for all any ideas ??

hi, i have more details about this problem. the scenario is: the extension 210 (analog extension) call to 207 (dbc4425 h323), and then , other extension for example 200 (dbc 4422 h323)call to 207. the call enter by the second line and speak perfectly with the extension 200. the problem is that...

Hi, i have a problem with this version of mxone and IP telephones dbc 42x02 series, i have configure one key with ODN2 (second line) , when i have a call i can take the second call ,the call is successful. The problem is that when I try to take the first call I had, the call is cut. any ideas??

any ideas for this issue?? Thanks Best Regards

hi, I have checked parnum , but not find any parnum for this isuue. Thanks Best regards

HI, i have a customer in TSW SP5 . i have a question about the monitored keys on DTS extension. i have a DTS extension with MDN keys, i have program the CALALT =2 for one monitored keys for ringing after delay, all works fine,but the problem is that i want to reduce the time of ringing after...

Hi, I have a problem with repair the Lim 1, I do all the procces but the result is not OK. 1-I install the telephony system in the lim 1 (without ICT), i connect to lim 1 and transfer the safety backup to /usr/backup. 2- unzip the file 3-go to the root partition as root user 4- tar -x...

Hi, I have Aspap 109 with value 3. Jitter buffer adaptive on for IP device boards Jitter buffer adaptive on for H.323 route boards can be the problem of the silent calls in my system, because the jitter buffer is 60 ms? the other aspap for example: PARNUM=191, PARVAL=20...

Hi I have a problem with IP Networking in one customer with the calls, The problem is that the calls are silent between both sides only sometimes. the configuration of the system is : In both side we have install ELU 32 board with 8 trunk. the configuration of the route is : <ROCAP:ROU=70...

hi mundus, I´m going to try put the SRT 1 in the dest and i say you the result of this

Hi, we have a TSW and a MX-ONE linked by IP Networking. But we have a problem when try to do a call back, it does not work. The configuration on both sides: /*MXONE*/ ====== MX-ONE Telephony System ====== Version: 3.2 SP2 build7 MDSH> roddp:dest=all...

Hello, We have one problem in one of our customer in BC10. When we remove a number from EX table (nanse:numtyp=ex,numse=xxxx) inmediately if they try to call to some extension the phone shows "destination does not exist" we send a LADAI command and all is ok again. Anu body has the same problem...

Hi, I have a MX-ONE 3.2 SP1 with a TLU83. Anybody could help me with the configuration route for analog trunk and for FCT too? Thanks!!

Hi all, i am testing the V24 type callinfo output through serial port of ESU. I have programed it but I dont get any data in the hyperterminal...I programmed as follows: MDSH> callinfo_output_set -output 1 -lim 1 -type v24 -subtype asb501 -dbname /dev/ttyS0 -bitrate 9600 -stopbits 1 -parity no...

Hi dstrang 1, I have 4 VSU in my system and all of them is working OK, the problem is that i need to put a new voice message but i dont know the extension of the VSU. I probed to restart all of the VSU board but the result is the same . any ideas? Thanks