Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by dark5tar

  1. dark5tar

    Inventory

    Assuming you have a DX... The version is listed in the text that the system outputs when you log in e.g 6.x.x 8.x.x 9.x.x You could list all the cards in the slots with LSLT A C then list all the trunks LTK A and all the extension numbers with LEX A I would have thought the maintenance...
  2. dark5tar

    Siemens Optiset E Memory Telephone

    Never seen one connected to a DX so maybe Hicom only. cheers
  3. dark5tar

    Hunt group - no answer

    Hi Rolead. Happymal was correct. rfd 9876 to 5432 rfd 5432 to 7654 job done after half a minute or so of ringing the caller will have hung up. why ring an empty desk? Use DND . and the call will step to the free hunt group members,if no one is there and they will get busy. cheers D*
  4. dark5tar

    Call recording on ACWIN

    Pressing the emergency button should record the call. The feature is designed for bomb threats etc. Give the button a press and see what happens. D*
  5. dark5tar

    optipoints version 9.0.0.71

    network busy? sounds like a translation sending the call down a trunk route with no trunks. No separate parameter for call from digital extensions I'm aware of.
  6. dark5tar

    Realitis Mail

    7-E-1 9600 they use a cli - no menus! A while since I worked on one, I think they are based on the vmx/octel so if you have programmed one of those or have the manual you should be ok.
  7. dark5tar

    I/C on operator grp is not working

    hi have you checked the night destination of the trunks? use the LTKD command and change with the RTK (dsa) command. the ns of the ops group is for assistance calls from extensions
  8. dark5tar

    ISDX Micro

    hi Joe It may be that the channels on this card are set to both or ROT sending on old software versions this could give busy when calling a voice mail system. list with LCH and change with SDT best
  9. dark5tar

    Obtaining a MAC/IP Address of an IP Phone

    Hi LDTE followed by the card address will show the IP addresses of the phones on that card. Not sure about the MAC address though.
  10. dark5tar

    Set auto answer and pre-recorded message for night bell

    Hello If your nightbells are connected to an extension port, (many are) DENs pretending to be DANs. Then put the answerphone in parallel and set to answer after 5 rings or so. If your bells are traditional dc bells then there used to be devices called level 8 diallers that picked up...
  11. dark5tar

    "number is a display number" when MEXing etc

    Hi Check for display number associations with the LDIS command then remove with the ddis command
  12. dark5tar

    50% of DX upgrages from siemens

    After a big of googling I found this http://www.enterprise-communications.siemens.com/uk/Products%20Clone/Infrastructure%20Clone/Communication%20Systems%20for%20Small%20and%20Medium%20Companies%20Clone/HiPath%20DX.aspx?tab=6 not sure if the offers are half price
  13. dark5tar

    DX ACD

    Hello, this answer depends on what software the system is running. First i'll assume later than 6.1 list the group with LACE <group number> check what R1FA (rad 1 forced answer) is set to; it should be N unless you want the callers to hear the message before ringing the agents Use LRAD...
  14. dark5tar

    iSDX DPNSS NSI's

    Hi 58B*AN iVM message waiting indication it's voice mail message waiting, normally followed by *1 or *0 to switch the message indication on or off. If you reject the message it does not usually get repeated how are you rejecting it? *94 s ? It may not originate from the isdx is there a...
  15. dark5tar

    Outbound CLI

    The commands for presentation numbers are rprs - use to program the digit strings to be displayed rpra - set display number for an extension rexf - to activate I've not tried this though, and I think your lines need to be isdn30e rather than dass you could also try adding exd (ex-directory)to...

Part and Inventory Search

Back
Top