Recent content by CentralJIM

Dear Firebird / Bignose21 Thanks so much on your advised and support I'll check RDB and LD17 RCAP. Happy New Year!!![cheers] BR

Thanks you very much Firebird I have check DCH RCAP and it was COLP. What is the correct reply for this please Thanks

Dear Gents, Need help please. We have a PRI external E1 link to an IP CISCO telephony. Problem is whenever I dial an IP extension to this route the Caller ID of my NORTEL CS1000 station is not on the display of the IP phone. The IP display says "unanimous" But CS1000 PRI to another CS1000 PRI...

Yes. We tried the procedures on the PDT reset password mechanism and an issue came up. The new password we input is not accepted. We input all format of passwords according to the procedures but failed. Not accepted. Any thoughts please. Thanks

Thank you very much bignose21. The release is 4.50W. CPU Processor CP PIV NT4N39. Im getting OVL428 upon Log in. PDT password reset mechanism was tried before but failed. It wont accept the new password. It says new password is incorrect and not accepted. Thanks

Dear, We have a CS1000M SG PABX in which is currently out of redundancy. Also the Log in password credentials has issues. We cannot log in to the PABX. Several attempts were done on the passwords all failed. All is working perfectly on the pass few months even we cannot log in. Currently I...

Guys @bignose21 & firebird Thank you very much for your guidance. The dialing sequence is now working. created a new SPN 011. Regards[bigsmile]

@ bignose21 thank you very much. I need to try that configuration when I deploy to that particular Site and update you accordingly. @ firebird thank you very much on the attachment utility. regards

Hi Bignose21. Thank you very much. I should try your advised. For further information TELCO route E1 R2 is full access. Full facility for local and national calls. local call 011+7 digits & national call 012, 013 & 05+8 digits for mobile phones(05XXXXXXXX) That's why SPN 01 & 05 has RLI 30 going...

Hello Guys. Hope you are fine @ firebird - I will try to run and check the attached file. TVM @ bignose21. SPN below FEAT NET TRAN AC1 TYPE SPN SPN SPN 01 FLEN 0 INPL NO RLI 30 >>>>>>>>>> TELCO E1 R2 route SDRR NONE ITEI NONE SPN 05 FLEN 0 RLI 30 SDRR NONE ITEI NONE SPN 1 FLEN 0 RLI 15...

Guys Thanks @ firebird - yes we are using SPN. NXX and NPA are not allowed to be configured with a leading 0 @ bignose21 - country is KSA. local codes are 011,012,013 followed by the 7 digit. DNB for 9 is AC1. if a phone is defined as Tgar 13,NCOS 6, TLD the call is directed to a TELCO E1 R2MFC...

Guys any help or suggestions please. Thanks

Hi Bignose, in LD 90, NPA is not define. in CRNO 3 INIT is ALOW. DENY is 71,73 & 75. thank you in advance

Hi bignose sir. thank you for your advised. for clear pic as below please: Route 10 - TGAR 13 - NCOS 6 - access 9 - national/local call no problem at 9-011-492XXXX or 9-012+7 digits & 9-013+ 7 digits. assigned only on selected extensions. Route 20 - TGAR 13 - NCOS 3 - access 9 - local call only...

Hello Guys. I know my question is easy for you on our legacy NORTEL Option 81c PABX. Our TELCO now requires 10 digit to dial outside 9-011-2553333 from 7 digit dialing 9-2553333.We use NCOS 3 for this local dial on 7 digits and we have a local call route. We have a route in which we can dial...