Recent content by amcomsoft

Well I have another dumb question. Configuration: Option 81c - NT5D11 lineside T-1 card Each line configured as a 500 set TYPE 500 CDEN 4D CUST 0 WRLS NO DN 1001 0 MARP CPND NAME ADMIN MAIN...

can it be configured as a d4 ami loopstart trunk and not use the pri functionality

Essentially I need to know if I can configure the NT5D12 to be a D4 AMI loopstart with the ports setup as 500 sets. I am not swapping out the 11 for the 12. I have a customer that has the 12 which I have not worked with before. I have worked with the 11 before and configured it as above and am...

The PBX is an Option 81c

I can not verify the part number as I do not have access to the system. This is what I have been told by the switch tech on site.

I have a configuration on a NT5D11 lineside T1 card and I am wondering if it is possible to use a NT5D12 and get the same type of configuration. The lineside card is setup as D4 AMI loopstart and the ports are setup as 500 ports in LD 10 (exactly like a typical analog port). Can something...

When I hit submit I realized I did not describe the problem very well Right now I am trying to use a Dialgic PBX card (D/82JCT) to try and get DNIS info from the switch but all I am currently seeing is some type of ANI (the station the called the dialogic card). For example I set up 3 stations...

Is it possible and if so how do I set it up: To have a call to a certain number be forwarded or transfered to another station from the switch. Possibly remote call fowarding. Right now I have a station set up so when I call that station from another it will automatically forward it to another...

I do not get any errors, the Dialogic card just does not see them apparently. I have 8 lines on all the odd number tn's (1 3 5 7 9 11 13 15 and the sample apps that came with the dialogic card appear to be working. I did the STAT 5 and the odd tn say '2616 idle' the even say 'UNEQ'

I seem to be getting a lot closer, is there any reason I can only use the odd number tn's? for example if I use TN 5 0 or 5 2 it does not seem to do anything for me. But if I use 5 1 and 5 3 I now have 2 lines up and running.

What is the difference with the voice and data units, with the 2616 do I need to use the data units at all?

I looked for the option menu in the CDB but could not see where to enter in the MCI

This switch is not set up as our office switch. We have another for that purpose. I am not sure if there is a voice mail system on this switch or not. The option 11 is just one we have for testing. The TN is 005 0 00 01 TYPE 2616 CDEN 8D CUST 0 AOM 0 FDN TGAR 1 LND NO NCOS 0 SGRP 0 RNPG 0...

Unfortunately I do not have anything to copy. As far as I know it is just the requirements in the initial post but for example I can not use MWA in the CLS or MCK, MIK in the KEYS 4 and 5 unless something is enabled in the CDB. I am trying to use it with this guy...

I need to configure/program an Option 11 with these configuration requirements. CLS - CTD FBD WTA MTD FNA HTA ADD HFD MWA CNDA TYPE - 2616 HUNT - (5502) IS NEXT PHONE IN GROUP LHK - 1 KEY 0 - SCR 5501 (RINGING CALL APPEARANCE) KEY 3 - TRN KEY 4 - MCK KEY 5 - MIK Now here is the problem except...