Centralized VoiceMail

NEAR SYS A û begin exts @ 2221
You must disable the card first, program the card for PRI, then re-enable the card.

To Disable / Enable Card
From Terminals & Sets û Next until you get to Maintenance û Show
Next until get to Module Status û Show
Show module û Next
KSU (1): State
0 Ports Busy û Press Disable or Enable
Disable at Once? û Yes

Protocols & Signaling
Hardware û Show
Show Module û Next
Cards on KSU û Show
Cd1 û KSU: Change to PRI û Show
Card Type PRI û Next
Lines: 001-023 û Next
Protocol: SL1 û Next
Type: MASTER - Next
Bchanseq: ASCEND û Next
CO Fail: TIAû547A û Next
IF Levels: ISDN û Next
Framing: ESF û Next

Internal CSU: OFF û Next (for back to back configs turn off. For PTP config through Telco turn On.

DSX1 Bld: 000-100
Line Coding: B8ZS
ClockSrc: Primary
Max Transits:31 û Next
End- of- list

Re-enable the Card

Header back to Maintenance û Back Until you see System Programming Show
Hunt groups û Next until you see
RecÆd # length: 3
Change to 4

Build target lines for each AND EVERY ext with the recÆd digits of the ext. Then assign them to Ring Only on the ext.

From Lines û Show
Show LN: 157 û Show
Trunk/ Line data û Show
Target LN û Next
Line type: Public û Next
RecÆd #: 2221
If Busy: to prime û Next
PrimeSet: 2221 û Next
Dstnct rng: None - Next
Aux. ringer: N - Next
End of list

Now go under Terminals&Sets and assign target line 157 to ring only on the phone.

Do this for each extension. Including the first port of the vmail.

Header back out and go into
Terminals&Sets û Show
Show set: ___ - Enter first ext #
2221:2221 û Show
Line Access û Show
Line Assignment û Next
Line Pool Access û Show
Line pool A: Y û Press next until you get to PRI-A and make sure it is set to YES.

DonÆt forget the vmail ext also

Then Build a Route

Services û Show
Ringing Service û Next to
Routing Service û Show
Routes û Show
Show Route: 003 û Show
Dialout: No Numbr û Next
Use: pool A û Change to PRI û A
DN Type: Private


Build Destination Code

Routing Service û Show
Routes û Next
Dest Codes û Show
None defined û Add
DstCode: 3 * (any) û Ok
Normal Mode û Show
Rte 000 û Change to Route 003
Show
AbsorbLength: 0 or none
End-Of-List

Then Header back out and go into System programming û Show
Hunt groups û Next until you see Dialing Plan û Show
Private network û Show
Type: None û Change to CDP û Next
PrivNetId: 1 û Next
Priv DN len: 4 û Next
End-Of-List

Header back and go back into
Terminals&Sets û Show
Show set û Enter VMail DN
2238: 2238 û Show
Line Access û Next to
Telco Features û Show
Feature Assign û Show
Show line: ___ - Enter the target line assigned to the Vmail DN.
Line 170: Line 170 û Show
Caller ID set: N û Next
Extl VMsg set: N û Change to YES

Assign the Auto Attendant to answer the target line assigned to the Vmail DN.
Feature 983 û Log in.
AA
Lines
Line 157 (for example)
Change the answer status to AA
Table 1
Rings 0

Enable the External Initialization option
Feature 983 û Log in
Dial 77
External init: N û Change to YES.

Enable Redirect DN
Feature 983 û log in
Dial 8
Redirect DN: N û Change to YES


FAR SYS B - begin exts @ 3221

You must disable the card first, program the card for PRI, then re-enable the card.

To Disable / Enable Card
From Terminals & Sets û Next until you get to Maintenance û Show
Next until get to Module Status û Show
Show module û Next
KSU (1): State
0 Ports Busy û Press Disable or Enable
Disable at Once? û Yes

Protocols & Signaling
Hardware û Show
Show Module û Next
Cards on KSU û Show
Cd1 û KSU: Change to PRI û Show
Card Type PRI û Next
Lines: 001-023 û Next
Protocol: SL1 û Next
Type: SLAVE - Next
Bchanseq: DESCEND û Next
CO Fail: TIAû547A û Next
IF Levels: ISDN û Next
Framing: ESF û Next

Internal CSU: OFF û Next (for back to back configs turn off. For PTP config through Telco turn On.

DSX1 Bld: 000-100
Line Coding: B8ZS
ClockSrc: Primary
Max Transits:31 û Next
End- of- list

Re-enable the Card

Header back to Maintenance û Back Until you see System Programming Show
Hunt groups û Next until you see
RecÆd # length: 3
Change to 4

Build target lines for each AND EVERY ext with the recÆd digits of the ext. Then assign them to Ring Only on the ext.

From Lines û Show
Show LN: 157 û Show
Trunk/ Line data û Show
Target LN û Next
Line type: Public û Next
RecÆd #: 3221
If Busy: to prime û Next
PrimeSet: 3221 û Next
Dstnct rng: None - Next
Aux. ringer: N - Next
End of list

Now go under Terminals&Sets and assign target line 157 to ring only on the phone.

Do this for each extension.

Header back out and go into
Terminals&Sets û Show
Show set: ___ - Enter first ext #
2221:2221 û Show
Line Access û Show
Line Assignment û Next
Line Pool Access û Show
Line pool A: Y û Press next until you get to PRI-A and make sure it is set to YES.

Header back to Line Access û Next
Capabilities û Show
Fwd no answer û Next until you see
Allow Redirect: N û Change to YES.

Header back to Capabilities û Next to
Telco Features û Show
Feature assign û Show
Show line: ___ - Enter the target line assigned to this phone.
Line: 165 : Line 165 û Show
Caller ID set: N û Next
Extl VMsg set: N û Change to YES.

Do this for every extension/ target line.

Then Build a Route

Services û Show
Ringing Service û Next to
Routing Service û Show
Routes û Show
Show Route: 003 û Show
Dialout: No Numbr û Next
Use: pool A û Change to PRI û A
DN Type: Private

Build Destination Code

Routing Service û Show
Routes û Next
Dest Codes û Show
None defined û Add
DstCode: 2 * (any) û Ok
Normal Mode û Show
Rte 000 û Change to Route 003
Show
AbsorbLength: 0 or none
End-Of-List

Then Header back out and go into System programming û Show
Hunt groups û Next until you see Dialing Plan û Show
Private network û Show
Type: None û Change to CDP
PrivNetId: 1- Next
Priv DN len: 4 û Next
End-Of-List

Header back out and go into
Telco Features û Show
VMsg ctr tel#s û Show
VMsg Center 1 û Show
Use: Line û Change to Routing tbl
Tel# - Enter the Vmail DN of sys A