Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
How to setup PRI
Basic Norstar Programming
1. Obtain your key code using the PRI enabler
2. Step 3 on the enabler shows you how to enter the 24 digit pass key to the system.
3. In maintenance disable Mod 2, Cards 1 or 2 depending on where your DTI card(s) are installed.
4.After you disable the card slot(s) go to the hardware section of programming and change the slot(s) from loop to PRI
5.Note before you enable the card(s) in Maintenance, you must enter in all the protocols for your span to work properly.
Example
DMS-100
BCHANSEQ: DESEND OR ASSEND= use to opposite of TELCO
COFAIL:TIA-547A
I/F LEVELS:ISDN
FRAMING: ESF OR SF
INTERNAL CSU: ON OR OFF: LEAVE ON
CSU LINE BUILD:0
LINE CODING: B8ZS OR AMI: NORMALLY SET TO B8ZS
CLOCKSRC: PRIMARY OR SECONDARY
6.Program routing Services follow these steps
Under Service press show once, press next 2 times,
press show to routes, press show, enter 001 in the field
press show, press next.
Under Use: Set to PRI-A or PRI-B, for SrvcType use public
Note in order to use the #9 for access you must go to system programming, Access codes , to Ext codes and change
this parameter from 9 to none..........
Press heading twice, next once to Dest Codes , press show, press next Dest Codes:9. ( the . is used as an any key, and must be set )
Press show the display shows normal: set to 001
Press show the display shows AbsorbLength: set as 1
Program the same here for Night: (normal:001 and AbsorbLength: 1
7. Under Terminal and sets make sure you program PRI-A
or PRI-B in the pool and icm as prime
8. Under line programming setup your target lines.
Target lines start at co 145
I have more information if needed however this should give you the basics for setting up PRI... Good Luck !!!!![[thumbsup2]](/data/assets/smilies/thumbsup2.gif "[thumbsup2] [thumbsup2]")
2. Step 3 on the enabler shows you how to enter the 24 digit pass key to the system.
3. In maintenance disable Mod 2, Cards 1 or 2 depending on where your DTI card(s) are installed.
4.After you disable the card slot(s) go to the hardware section of programming and change the slot(s) from loop to PRI
5.Note before you enable the card(s) in Maintenance, you must enter in all the protocols for your span to work properly.
Example
DMS-100
BCHANSEQ: DESEND OR ASSEND= use to opposite of TELCO
COFAIL:TIA-547A
I/F LEVELS:ISDN
FRAMING: ESF OR SF
INTERNAL CSU: ON OR OFF: LEAVE ON
CSU LINE BUILD:0
LINE CODING: B8ZS OR AMI: NORMALLY SET TO B8ZS
CLOCKSRC: PRIMARY OR SECONDARY
6.Program routing Services follow these steps
Under Service press show once, press next 2 times,
press show to routes, press show, enter 001 in the field
press show, press next.
Under Use: Set to PRI-A or PRI-B, for SrvcType use public
Note in order to use the #9 for access you must go to system programming, Access codes , to Ext codes and change
this parameter from 9 to none..........
Press heading twice, next once to Dest Codes , press show, press next Dest Codes:9. ( the . is used as an any key, and must be set )
Press show the display shows normal: set to 001
Press show the display shows AbsorbLength: set as 1
Program the same here for Night: (normal:001 and AbsorbLength: 1
7. Under Terminal and sets make sure you program PRI-A
or PRI-B in the pool and icm as prime
8. Under line programming setup your target lines.
Target lines start at co 145
I have more information if needed however this should give you the basics for setting up PRI... Good Luck !!!!