Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chris Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Scheduled download
3000 Series Firmware
Symptoms include but are not limited to: No dn displayed, but works, no softkeys or softkeys that are in the wronge place, and my favorite, transfers that work but don't give you the connect option so the caller ends up on park, forever..
We've had several post of late due to the new procedures required to download 3000 series phones.. For simple one station problems, a simple ld 32 fwvu x x x x and fdli x x x x will check the level of the set then force download a single station.. The good news is in ld 97 you can schedule all sets that are not current to match you harddrive. This was posted here over 2 years ago and i can't find the original post. It does work, we use it monthly.
This is an example of a scheduled download of (5) 3904 sets with TNÆs of 52-0-11-0 through 52-0-11-4.
One interval is scheduled to take place on Thursday at 3:00am for a maximum time of 2 hours
>ld 97
SCSYS000
MEM AVAIL: (U/P): 23534388 USED U P: 4855751 429313 TOT: 28819452
DISK SPACE NEEDED: 698 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ chg
TYPE fdl
FDTP 3904
FDTM yes û Say yes if you want to schedule the download, Say no if want it to start immediately
FDAY 5 1 û FDAY d n Day and number of time intervals for download (if you said yes to FDTM)
d= (0-6) Day of the week, Sunday to Saturday
n= (0-4) Number of intervals where 0= no download for that day
note: If two or more intervals are specified, they must be non overlapping,
non consecutive and in increasing order.
FDAY is re-prompted until <cr> is entered.
FINT 3 2 û FINT s l Starting hour and length for a time interval.
s= (0-23) Starting hour using 24 hour format
l= (1-24) Length of interval in hours
FINT is prompted n times if Number of Intervals
is > 0
FDAY <cr> -- FDAY is re-prompted until <cr> is entered.
FTNR yes û Say yes to download to specific range of TNs, Do not say no to this unless you want all 3904's to download
FSTN 52 0 11 0 û Loop, Card, Shelf, Unit Starting terminal number for download
FETN 52 0 11 4 û Loop, Card, Shelf, Unit Ending terminal number for download
FDNR no û enter no because we donÆt want to select specific DNÆs for download.
FRCE yes û Say yes to force the download regardless of the 3904Æs current flash firmware version. (i use no for this one)
FVER <cr>
MEM AVAIL: (U/P): 23534388 USED U P: 4855751 429313 TOT: 28819452
DISK SPACE NEEDED: 698 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ ****
OVL000
Now that the schedule is create, we must activate it to run
>ld 32
NPR000
.fdls û This command initiates the system wide flash download to all or the specified 3904 sets according to
the parameters specified in LD 97 FDL configuration
BUILDING TREE ..
TRIGGERING DOWNLOAD NOW
>
TIM661 14:52 30/6/2004 CPU 1
SDL005 M3900 DOWNLOAD STOP HOUR (14 )WEDNESDAY -- This is what you see after FDLS successfully
completes is startup of the schedule.
This is what you will see in the PBX during the time the downloads are taking place.
TIM661 03:00 2/7/2004 CPU 1
SDL004 M3900 DOWNLOAD START HOUR (3 )FRIDAY
SDL001 STARTING DNLG 52 0 11 0
DTC001
SDL000 3904(52 0 11 0 ), VERSION 83, BKGD MODE.
SDL001 STARTING DNLG 52 0 11 1
TIM661 03:15 2/7/2004 CPU 1
SDL000 3904(52 0 11 1 ), VERSION 83, BKGD MODE.
SDL001 STARTING DNLG 52 0 11 2
DTC001
SDL000 3904(52 0 11 2 ), VERSION 83, BKGD MODE.
SDL001 STARTING DNLG 52 0 11 3
TIM661 03:30 2/7/2004 CPU 1
SDL000 3904(52 0 11 3 ), VERSION 83, BKGD MODE.
SDL001 STARTING DNLG 52 0 11 4
SDL000 3904(52 0 11 4 ), VERSION 83, BKGD MODE.
SDL002 M3900 DOWNLOAD COMPLETED -- All were downloaded successfully
TIM661 03:45 2/7/2004 CPU 1
You can check the firmware level of the phones specified in LD 97Æs schedule by using the FSUM ALL or individually by using the command FWVU L S C U command in load 32
ld 32
NPR000
.fwvu 52 0 11 0
AUD000
****M3900 VERSION REPORT****
TERMINAL TYPE = 020
CORE FIRMWARE VERSION = 024
FLASH FIRMWARE VERSION = 083 û We are looking for this 083
.fsum all
TYPE:3904 CUST:00 PDN:773803 TN:052 0 11 00 FW:083 û Or this 083
TYPE:3904 CUST:00 PDN:773804 TN:052 0 11 01 FW:083
TYPE:3904 CUST:00 PDN:773805 TN:052 0 11 02 FW:083
TYPE:3904 CUST:00 PDN:773806 TN:052 0 11 03 FW:083
TYPE:3904 CUST:00 PDN:773807 TN:052 0 11 04 FW:083
We've had several post of late due to the new procedures required to download 3000 series phones.. For simple one station problems, a simple ld 32 fwvu x x x x and fdli x x x x will check the level of the set then force download a single station.. The good news is in ld 97 you can schedule all sets that are not current to match you harddrive. This was posted here over 2 years ago and i can't find the original post. It does work, we use it monthly.
This is an example of a scheduled download of (5) 3904 sets with TNÆs of 52-0-11-0 through 52-0-11-4.
One interval is scheduled to take place on Thursday at 3:00am for a maximum time of 2 hours
>ld 97
SCSYS000
MEM AVAIL: (U/P): 23534388 USED U P: 4855751 429313 TOT: 28819452
DISK SPACE NEEDED: 698 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ chg
TYPE fdl
FDTP 3904
FDTM yes û Say yes if you want to schedule the download, Say no if want it to start immediately
FDAY 5 1 û FDAY d n Day and number of time intervals for download (if you said yes to FDTM)
d= (0-6) Day of the week, Sunday to Saturday
n= (0-4) Number of intervals where 0= no download for that day
note: If two or more intervals are specified, they must be non overlapping,
non consecutive and in increasing order.
FDAY is re-prompted until <cr> is entered.
FINT 3 2 û FINT s l Starting hour and length for a time interval.
s= (0-23) Starting hour using 24 hour format
l= (1-24) Length of interval in hours
FINT is prompted n times if Number of Intervals
is > 0 FDAY <cr> -- FDAY is re-prompted until <cr> is entered.
FTNR yes û Say yes to download to specific range of TNs, Do not say no to this unless you want all 3904's to download
FSTN 52 0 11 0 û Loop, Card, Shelf, Unit Starting terminal number for download
FETN 52 0 11 4 û Loop, Card, Shelf, Unit Ending terminal number for download
FDNR no û enter no because we donÆt want to select specific DNÆs for download.
FRCE yes û Say yes to force the download regardless of the 3904Æs current flash firmware version. (i use no for this one)
FVER <cr>
MEM AVAIL: (U/P): 23534388 USED U P: 4855751 429313 TOT: 28819452
DISK SPACE NEEDED: 698 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ ****
OVL000
Now that the schedule is create, we must activate it to run
>ld 32
NPR000
.fdls û This command initiates the system wide flash download to all or the specified 3904 sets according to
the parameters specified in LD 97 FDL configuration
BUILDING TREE ..
TRIGGERING DOWNLOAD NOW
>
TIM661 14:52 30/6/2004 CPU 1
SDL005 M3900 DOWNLOAD STOP HOUR (14 )WEDNESDAY -- This is what you see after FDLS successfully
completes is startup of the schedule.
This is what you will see in the PBX during the time the downloads are taking place.
TIM661 03:00 2/7/2004 CPU 1
SDL004 M3900 DOWNLOAD START HOUR (3 )FRIDAY
SDL001 STARTING DNLG 52 0 11 0
DTC001
SDL000 3904(52 0 11 0 ), VERSION 83, BKGD MODE.
SDL001 STARTING DNLG 52 0 11 1
TIM661 03:15 2/7/2004 CPU 1
SDL000 3904(52 0 11 1 ), VERSION 83, BKGD MODE.
SDL001 STARTING DNLG 52 0 11 2
DTC001
SDL000 3904(52 0 11 2 ), VERSION 83, BKGD MODE.
SDL001 STARTING DNLG 52 0 11 3
TIM661 03:30 2/7/2004 CPU 1
SDL000 3904(52 0 11 3 ), VERSION 83, BKGD MODE.
SDL001 STARTING DNLG 52 0 11 4
SDL000 3904(52 0 11 4 ), VERSION 83, BKGD MODE.
SDL002 M3900 DOWNLOAD COMPLETED -- All were downloaded successfully
TIM661 03:45 2/7/2004 CPU 1
You can check the firmware level of the phones specified in LD 97Æs schedule by using the FSUM ALL or individually by using the command FWVU L S C U command in load 32
ld 32
NPR000
.fwvu 52 0 11 0
AUD000
****M3900 VERSION REPORT****
TERMINAL TYPE = 020
CORE FIRMWARE VERSION = 024
FLASH FIRMWARE VERSION = 083 û We are looking for this 083
.fsum all
TYPE:3904 CUST:00 PDN:773803 TN:052 0 11 00 FW:083 û Or this 083
TYPE:3904 CUST:00 PDN:773804 TN:052 0 11 01 FW:083
TYPE:3904 CUST:00 PDN:773805 TN:052 0 11 02 FW:083
TYPE:3904 CUST:00 PDN:773806 TN:052 0 11 03 FW:083
TYPE:3904 CUST:00 PDN:773807 TN:052 0 11 04 FW:083