iS3000 Projecting Software 1

[81k3r80y2]

Dear All...

Is there any software to create projecting file of iS3000 ?
The software supposed to be Windows based, or has Graphical User Interface.

I'm very disappointed with OM Tool...

I only found POMView which is only for view & analyze project files.

Thank you in advance.

rgds,
Wiku

 

[LarsenDK]

Hi
To my knowlegde there are no tool like you ask for.
Only SM410 or magnement@net, but they are for endusers, and not intented to fully build a IS3000 config.
I personly think that OM is the strongest tool around, also comperred with other pbx´s, You can realy do nice things (and some realy bad) with OM.

What do You need to do, maybe I can help You out ?

Regards
Jan

 

[81k3r80y2]

Thanks Larsen...

What I need to do now is to build new 9 units iS3030 to replace existing ECS-FX.

New iS3030 must consist existing numbers and trunks and will have new CAS subscribers and digital trunks.

If I have to type one-by-one for each iS3030, then it will be exhausted work.

Is there any software that I could select the service and give the numbering plan, so the software will automatically generate the "projecting file" that I could load to iS3030.

Thanks,
Wiku

 

[81k3r80y2]

Thanks Larsen...

What I need to do now is to build new 9 units iS3030 to replace existing ECS-FX.

New iS3030 must consist existing numbers and trunks and will have new CAS subscribers and digital trunks.

If I have to type one-by-one for each iS3030, then it will be exhausted work.

Is there any software that I could select the service and give the numbering plan, so the software will automatically generate the "projecting file" that I could load to iS3030.

Thanks,
Wiku

 

[wernergo]

Hi wiku,

it is a lot to do.
I would make a standard hardware configuration, if possible, to load in each of 3030.
For DNR I list them with CHDNRC: and HWA in Excel, then save as CSV. With Editor make a File with compleet OM-Syntax, and save it as *.scp File.
With SMPC or SysMgr410 run the script.
For FCM and TRFC and so on.
I do it so, many times, it is a quickly methode

If you have questione, say it or mail me

regards Werner

 

[81k3r80y2]

Hi Werner,

Thank you for your suggestion.

Is it possible for me to have one example of your excel files ?
You may put it on

http://www.rapidshare.com

Thanks in advance,
Wiku

 

[wernergo]

Hi Wiku

In the dnr.xls you can see the OM-command with the DNR chdnrc:1000, then shelf, board, circuit.

You must save it as csv-file, look dnr.csv, the separator is semicolon.
Rename it to *.txt, for the editor ( must not be, like you work with an editor )

With an editor you must change the semicolon to comma ( decimal point ) and put a semicolon to the end of the rows.
Save this as dnr.scp.

I think you know to work with scriptfiles.

If I have to create a new OM-port , I allways take a script, allso for chabnr or for private calls aspicc and so on.
If you know many OM-commands, it is possible to create some configurations offline, only with editor.
Look at my files for OM-Port vdu02_3030.scp, asblock3.scp, many boards in a 3070 asbrds.scp or PMX with all lines s2m12_9.scp.

If you have one file it is easy with the right editor, with copy and paste or replace to create any new file.
The best editor, I think is UltraEdit, because you can edit also columns.

Enjoy yourself

Werner

p.s. I´m not a member of rapidshare, better it is to mail.


the file is very small, I hope you can receive it

http://rapidshare.com/files/21025732/_Sopho_script.zip.html