Search results for query: *

No. I am looking basically for connection (or possibly a service) that I can essentially make a cellular call to PSTN line which is my direct connect to a PBX command line interface. Desired scenerio is this: 1. monitoring service recieves an alarm from a modem equipped POTS line attached to...

Would like to configure my HTC Inspire to be able to link to my PC in order to modem into sites if internet access is down. I am not always near a landline I can use. Would like to know best software for this purpose and if I can configure Putty to use the (I assume) usb link and how to in...

Thanks I will check. Sh Run shows transparent mode and extended spanning-tree enabled. I am wondering if I have corruption and thinking of upgrading the IOS, but that carries additional risk since I haven't done it before.

C2950-I6Q4L2-M Ver 12.1(12c)EA1, release software (fc1) I don't see either an EI or an SI in the boot up or on the switch ports are 12 fastnet 802.3. I don't know where else to look. Hate to just keep throwing numbers at you, but I am hoping these make sense.

I am trying to do a lab for extended vlans in a lab I created at home. everytime I try to create vlan 4010 e.g. in global config mode it gives me "error: VLAN 4010 is not user-configurable" I am running transparent, extended spanning-tree id is enabled. I am using a 2950 IOS12.1 I have...

I am going to try this after hours. Tremendously helpful if it works for me as well as it did for you.

Thank you hadn't thought to check my patches. I am already running SU0801 including the Q02024284-03, so I may have to refer this to the vendor or re-install the patches.

I don't usually do this so I think I must be missing something simple. Trying to create an agent to skillset schedule. changes made in assignments then moved on to the schedule, created a description , reset button, set time, set calender for start, set schedule (weekly), tried to build a reset...

I have customer that wants to know if he can use privacy release on an MCR line to effectively allow every one with that MCR to join in. kind of a mini-group conference.

How do I go about this. 4.0 succession software on a 61 with old hardware 2921 swaps every night. I have Call Pilot 5.0 and CCMS 6.0 tied into it

I did not. Thanks. Thought it was a hard key.

I have installed several 1140E phones and can't get the msg/inbox key to work. Checking with Nortel I have been unable to find more than the proviso "msg/inbox key may not function with all systems - check with your administrator". I checked with myself and I still don't know. What gives?

I appreciate the responses. Kind of what I was expecting...you can do it but you won't like it type of thing. Don't think the customer will spring for 6xxx phones but it's a good idea. I will advise them. Thank you for the help.

We added a 2211 ip phone recently with 3 rollover lines at a remote location for the customer, so Far so good. Now the customer wants to add an ACD position to this phone. Can this be done? Ultimately they want an ACD agent and 4 more lines on this little guy. I have told him I am dubious but am...

John, Thanks for your input. I figured out how to make it work. These are XUTs on the Nortel end and OPXs on the fujitsu side. By building a CDP TSC and referring it to a RLI with a DMI that inserts 099, I am sending the dial pulse code (09) for * before the second 9 which triggers routing to a...

First make sure you still have input from the radio at whatever COT you have programmed for the music route. Make sure you have a COT in EACH networkgroup you have in your switch. example TKTP MUS ROUT 49 DES MUSIC TN 072 0 14 00 MBER 1 MUSIC TN 020 1 11 02 MBER 2 MUSIC TN 040 0 14 00...

Actually I already did that, but the fujitsu does not see the *. I thought perhaps I was only creating a pause which was being outputted on the trad, but the symbol was not actually being sent. I guess I need to find a digit grabber somewhere to prove or disprove my output. Thanks

I appreciate the help, however, I literally meant *9. The fujitsu wants to see the * symbol. This can be done off a SL100, but I need to know if it can be done with the 81C

Trying to satisfy a code request from a Fujitsu on the other end. Setup is this ..4 loop COTs appearing as OPX on the fujitsu end need to send *9 from my DMI for LD access. If I can do it I haven't figured out how. Any help?