Search results for query: *

Why don't you just give them 800 numbers? Some carriers will allow you to go on line to change where the 800 numbers ring to. You dont need any equipment at all for this.

OzzieGeorge, Thank you for you attempt. No. I am not using LCR at all and No all my stations are in the same tenant. However, my trunks are in tenant 02 and all my stations are in tenant 01. I am still confused. Would the phone system treat analog different than digital even thought they...

When I dial out, it grabs an outside line but it does not send all the digits out. I always get an intercept message, the number you have dialed is not in service. Any help is apprecaited.

I have an IPS2000 with a regular T1 (not pri) and digital stations can dial fine.

For some reason I cannot dial from my analog phone via the T1. It seems that nor all the numbers are being sent. I can dial fine via the pots lines. suggestions?

Thanks. I thought there is something I could do. Thanks to all of you.

for one day this week, one of my users had over 2000 NDR records for email she never sent. Why? How can I stop it? Has someone hacked her user id?

Impossible. If you are on the speaker and it switches to the handset, and the handset is on hook, the call would disconnect.

Impossible.

I would like to consider the max. I am not about to propose anything less than that as the battery has to be designed to support any ugprade to more station ports. Curretnly there are 3 cabients which are almost full. 32 trunk ports and 60 analog stations and the rest digital. Could tell me...

How do I decide what kind of battery backup to purchase for the system i.e. how much amps and wats that it would require?

There are some other caveates about where to put the ISDN card. In the earlier versions of the Elite, it takes up 3 slots!!!

a. I wanted to know if faq955-6699 applies to MS Exchange Small Business Server too? or just MS Exchange 2003? b. How can I see if I have Service pack 1 or 2 in exchange? c. How can I reduce my stm file? The total size of all my mailboxes in only 12gb but my total size in teh directory is...

Is it possible to forward from in CCIS as follows: site A Site B 200 300 E600>200:3,00 E603>300:2,99 (pilot for voicemial) Note> 299 is the voicemial. If you call 300 - it goes to voicemial. if you call internally from site a or if a trunk calls comes in from...

The customer misplaced the EU24 cable. Does anyone know the pin outs so I can replace it? I guess it is not a straight thru cable. or if not, what is the part number for the cable between the EU and the phone?

Imeldesign, Yes. That is what I do either busy out the port in command E50 or reboot the phone system after hours. I think restarting the voicemail would also do it only I do not have remote access to the voicemail and it is easier for me to restart the phone system remotely. The voicmeial is...

either a reboot of phone system or voicemial clears it up. What should I be looking for? why would the port stop answering?

Wayne50 - i hope you dont mind me saying so - but you do not make it easy to help you. Why dont you start with posting each of the commands the all the techs have listed for you over hear and the results: 08>708>? 4000>0>? 4000>0>? F87>087>? F87>043>? CM08>443>? CM08>444>? 1225>vms stations>...

The posting you show indicates on a mismatch of protocols from the dialogic to NI2. If you have NI2 programmed on the NEC as well as the telco, there is no mismatch here. You say that you have a Telecordia variant of NI2. I don't know what that means but if it is not standard NI2 then maybe...

Thank you Belvedere. Here is what it said: F63>005FFF67 FF67:03 00 00 00 In what position did I need to see the 03? In the first position?