Search results for query: *

Sorry to come back later. My problem is resolved. It was due to a bad configuration of the devices and providers in the Microsoft Fax Service Manager. Here the link to verify the fax configuration on windows server: http://technet.microsoft.com/en-us/library/dd337301.aspx Thank you everybody

Yes we have the MSS server as the backend message store. And i check the COS in my voicemail subscriber and the Outbound fax calls set to Yes. Is there any special licence to do that or a particular parameter to configure? Emmanuel

OKi, We are Modulare Messaging V4.0 release 6.2.696.3 and we use the Voice Mail system configuration in the MAS where fax voice mail domain is configured. There is no exchange or Domino. I think it miss something in the MAS that it can not send the number of the fax.

We use mms with outlook. When we send a email, we have the reponse: "Your message to fax=4004@ xxxxxxx.com could not be delivered. user "fax=4004@xxxxxxx.com" unknown The undeliverable message is attached " And that, in internal or external fax number

Hello, We have a MM with a S8700. We received our fax in our mailbox by the MM. But we can not send fax by email. We have configured fax in voice mail configuration of the MAS. I think dialing rules are ok but for Microsoft Fax Service Manager, not sure. Have we forgotten something? is there is...

Hello, I have made the traces between vlan data and vlan voice. if that interests somebody, it can ask it to me. I will send him it in Excel file APPLICATION IP SOURCE PORT SOURCE IP DESTINATION DESTINATION PORT DESTINATION REMARQUE ADMINISTRATION @IP PC Administrateur 1 variable @IP S8300...

Ok, Sorry if my question is not clear. We have a firewall between Vlan data and vlan Voice. And I would like to know the ports to be open and which are flows which are exchanges between the S8300 which is in the Vlan Voice and the Softconsole, the Softphone and the PC where is the ASA...

Hello, Is there anybody who has a documentation on the flow which forward between ASA and the Softconsole, ASA and the Softphone, ASA and a pc on the LAN Thank you very much

We found the solution. It was a bad configuration of the ds1 for Switzerland. Thank you Catpainenick666, MaxEMEA

And we need 0 for anything beside calling out because in our feature access code, we have in Auto Route Selection (ARS) - Access Code 1: 0.

Yes, here the parameters of the DS1 and the trunk group config: display ds1 001V2 DS1 CIRCUIT PACK Location: 001V2 Name: DS1-OO1V2 Bit Rate: 2.048 Line Coding: hdb3 Signaling Mode: isdn-pri Connect: network TN-C7 Long Timers? n...

Yes, here the trace of a call to public network: me data 07:10:33 active station 4001 cid 0x1e4 07:10:33 G711MU ss:off ps:20 rn:1/1 10.32.143.150:25058 10.32.143.133:2050 07:10:33 xoip: fax:T38 modem:off tty:US 10.32.143.133:2050 uid:0x1a 07:10:34 dial 002...

Hello, the status trunk 1 show idle/inservice But when we call out, we have the busy tone. As we are in Switzerland, we think about the Coutry code. But we haven't the DS1 configuration for Switzerland...

Hello everybody, We put a S8300 with G700 in our custumer desk. But the problem is we can not call outside. The sig, the trunk, the IP-Network-Region are done as in the documentation. Please have you got an idea. Emmanuel

Thank you ABCIP. Finally we got the solution. There were wrongs parameters in the sig: Direct IP-IP Audio Connections? y IP Audio Hairpinning? y It was N instead of yes. bye bye

We have just changed the adress of G700, S8300 and IA 770. But the link between S8300 and messaging IA770 is down. We make busy release of the trunk, of the sig, but it is not succeeded. Have you got an idea? Thank you Emmanuel.