Search results for query: *

Thanks I think it will work now.

I think I have not explained what is going on well enough. I have a MICS 4.1 with a DTI card in slot 4 and a service card(clock card) in slot 2. The 2 port fiber card is in slot 1. The system will not boot with the 2port card installed at all. It boots fine without the fiber card. I have removed...

I have a MICS 4.1 with a service card in slot 2 a 2 port fiber card in slot 1 and a DTI card in slot 4. Problem is the system will not boot with this config(system says warm reboot, reset or OK), either option the system never boots. I have done a system default each time I changed the...

I have tried both cables and card status stays the same. I have a service card on the way and will try again monday morning. Hope to have good news. Thanks

I am good with the card locations. One thing the protocol for this PRI from AT&T is National NI2 and they are using a DS-100 switch.

We are using a service card(slot1) and a 2port fiber card(Slot2). I looped the DTI card directly with a loop plug and the state did not change. This is the second DTI card used so I am replacing the service card with a combo card. Will let you know thanks for the help.

There is a service card and clocking is set to primary.

I have a blinking yellow and green light. We have verified connectivity but the D-channel is not up.

I am working on a MICS 4.1 with a fractional PRIthat is not working. Here is what I have done. Loaded PRI keycode and DTI card is enabled as a PRI. Prog route 001 to use PRI-A Create dest code of 9and any Deprovisioned channels 11-23 using only 1-10 Disabled 11-23 in Link Status All phones have...

Exactly

Maybe you need to read the site policy thoroughly Curly. We do make mistakes and are not all knowing all the time like you. "The difference between genius and stupidity is that genius has its limits" ND>

I thought the question was pretty clear. What is the difference in the upgrade procedure for a NAM going from 4.0 to 4.1 versus 3.0 to 4.1. I know now that it is expected to include software version of the KSU I am working with. MICS 6.1 I do not have an old enough version to work with 3.0...

First I don't make anyone do a thing. I explained that I do not do NAM upgrades very often. Normally 4.0 to 4.1 no problem I have a 3.0 I am trying to upgrade and I was just looking to see if there was something I needed to do that I was'nt doing. I have used this site for many years as a...

First I work more with Call Pilots and rarely do my svc. calls include NAM upgrades. But when they do the unit is usually a 4.0 machine and my upgrade kit has worked perfectly until I came across this 3.0 machine. Are there steps that I am missing to upgrade a NAM from 3.0 to 4.1. Here are the...

I am trying once again to upgrade a 3.0 NAM to 4.1. I load the 4.1 boot disc and 4.1 upgrade CD and the display on the NAM goes from 7f to 00 like other upgrades I have done and beeps twice(30-40sec interval) then sings except the tones go down versus up like normal and the upgrade fails. I...

6.1 MICS. I think it was a bad NAM out of the box.

xfer the vmboot.exe file to a floppy?

The tones are descending after the upgrade procedure.

I upgrade VM and phone systems for the company I work for. I work more with the Call Pilots more often but occasionally NAM,s. I have upgraded many from 4.0 to 4.1 with no problem this is the first one that is 3.0. The unit sang after the upgrade but has not sang again since rebooting after the...

Any other ideas?