Search results for query: *

Can you program an NXX in an opt 81c running succession 3 as a single digit. Having all 2 , 3 , 4 ,etc. going to the same rli?

I assume you mean "That's the fix" as in dont use it. I think I learned my leasson on that.

I came in early today and did a hard reset of the PBX by shutting it of at the breakers. This fixed it. I geauss a zero got stuck and a hard reboot unstuck it. I tried disableing the shelf then the controller and reseat the controller, but that didn't work. Thanks for all the help and advice I...

Regreatably no I did not out them. I have tried the cardslt cmd and it doesnt seem to work for me. If I have an analog phone prog. on the card it say i can't because there is something on it. If I del. what's on it it say it can't because it is unequiped. Most likely I am not doing it correctly.

Thanks KCFLHTK and SL1M1 I will try that. I hope that will work and it's not a corrupted database.

What confuses me about this is the fact that I had analog lines working on the same TN's prior to me moving them to another card using LD 25. Then putting a digital card in the same slot, and it's not just one slot it's about 5 that I have moved and can't get the digitals to work on. I have...

When the phone is plugged in it blinks once then goes dead. There are other digital and analog phones on the same loop, and they work. I am using 2616 set's. Yes I have disabled and enabled ports with same result. I have IDC the card it is an NT8D02ea. DES TEST TN 020 0 12 01 TYPE 2616...

cmassjohn: Sorry about the are you serious comment earlier I read your post as cord not card. Yes I am using digital line cards. To clarify a little more. I moved a bunch of analog cards to empty slot on the same shelf. Then after the cables had been terminated to the new blocks we went back...

KCFLHTK: We have tried to reverse polarity and still doesn't work. cmasjohn: Are you serious about the digital line cord? I am outing the digital and programing the tn as analog OR digital, and putting the appropriate card in the slot. Thanks for the help

I have an 81c with succession 3.0 on it. We have been redoing the cabling on the TN side. Going from 66block to wire wrap. I have been using the mov command in LD 25 to move whole analog cards. The digitals I move one at a time and no ACD sets are being moved. It has been working fine until we...

I swapped both per sig cards and it seems to have done the job. At least nobody is complaining anymore.

Good advice Thanks. Can't do it without you sometimes.

I did the exact thing you suggested last night and got it working. I did discover that the satin line cords have to be plugged in a certian way. I had to flip all my line cords to get it to work. Thanks for the help.

I am having problems getting my system monitor cards NT8D22 working in my 81c. I have double and triple cheked all the dip switch settings. I have tried new cards and cards that I tested in my 61c that worked fine in the 61c. I did notice that in the installation instructions it shows an...

Thank you johnpoole, pronei and ghtrout. It was the way the paddleboard pinned out. Turns out that 6 on the paddleboard is the recv not 3 like it usually is. So 6 on board goes to 3 on dumb term. I found this info at http://www.ghtrout.com/ghtrout/index.html Thanks to all the other who tried...

The paddle cards are original to the switch.

The 9 pin RS232 plug is the same on both isn't it. I know the cores use a 25 pin, but I have a 25 to 9 pin adapter that I use.

Currently each switch is just set with defaults. What is vni?

I have 4 opt switches 2 81c and 2 61c. They are all networked together via cdp with 2 PRI's between each switch. Is it possible to route intercept treatment for all the switches to 1 central MIRAN card?

I have tried 2 other cards they are just the 2 port paddle boards, but I get the same result. If you mean wiring from the tty to the dumb terminal then yes im sure its good. I can use the same cables to access the core tty ports with the same terminal.