Search results for query: *

It should. As long as there are no programming conflicts. Use a crossover cable to connect the 2 systems.

The Sys ID would change after your upgrade from R1T1. Wait until after the upgrade to input the PRI KC. But after that, it would retain the new SW Sys ID. I have also been getting into the habit of writing or taping the sheet of the PRI KC and Auth# on the inside of the MICS door with the Sys...

Maybe I've just been spinning my head to get this working & I'm mostly there. Just a fried brain right now. I have networked Norstars previously, searched threads & FAQs. I have 2 MICS 7.1 using CDP,dest codes, routes, remote pkgs & have the 3 digit target lines set up in both systems...

I changed some programming for me to test & I only see me cell phone number come up when the Norstar set calls out. After alot of conference calls, testing & researching. What the off-site UM system is looking for is (NCD)Network Call Diversion. Called & Calling Party to their system to...

MICS 7.1, PRI with NI-2 I am trying to set up extensions to"FORWARD CALLS EXTERNAL" after 4 rings to a VOIP UM Platform. It is not recognizing the OLI of the sets that I programmed. The UM Center states that they do not see the DID number that I have in OLI. If I call from the set to my...

Would he not be able to program& set up remote access with a point to point T-1? You would page the main site as normal & then page the second site with *xxx.

On the EKS realm, I got to finally pull out an Eagle. About time!!! I've kept 5 spare systems for parts just in case. I should of just replaced it with an 8x24 to bring them up to last century. Of course the Eagles only came out in 83'.

If I remember correctly DR5.1 & MICS 4.0 started Page Timeout. All you can do is try again to teach the users on the shop floor to use the Rls button when done paging. You know when they aren't because it is not a silent hangup. Everyone will hear the "Auction House" effect. After a while...

Check the settings in Hardware first. Someone may have swapped the PRI card at some point. Make sure it shows Loop Start. It should also show either 25-28 or 31-34 depending on software level

I set up a school that the teachers just call into a hidden CCR prompt to a info MB. Or maybe use a group list. Have the users set up with notification.

Then do a Page All manually & hit a few keys or announce time to start working etc.

I think skutch makes a device.

Also make programming in Admin to VM "No". Then all calls will go go GD.

I had a power supply that the voltage was good but the amps were low.

I remember years ago setting up a time clock signaling for a wharehouse. It had nothing to do with the Norstar. It was from the Time Clock contacts to the Paging Amp. This should be your scenario with whomever the Bell signaling Mfg is. Separate contacts could be as simple as hooking up a...

Well I guess it is "FM". I tried yesterday & she passed me right in. I had reconfirmed with the person on site that nothing else was being done the other day. We'll see if stays this way. Thanks for the posts.

That is what I was thinking. Nobody on site knows how to get into programming. I was thinking maybe the I-RAD locked up, which is why I had them reboot. I just did not know if anyone ran into this situation also. Once in a blue moon I've been locked up with a FastRad over the years; a reboot...

It was working fine. I set it up on Wednesday (it was never previously set up) when I was onsite. I was physically into the system performing remote programming on Thursday in & out a few times between other remote tickets. Then maybe about the 4th time- "No Access" on the users display when...

I had been into a CICS 6.0 a few times programming successfully last week. Then all of a sudden when they try to pass me in (the same person), I hear the error tone & their display on the T7316 states "Access Denied". I had them reboot to no avail. I never ran into this on other systems. Any...

Sorry, I was given wrong info. I just double checked with the tech. He had only performed a level 1 reset.