Search results for query: *

I failed to follow-up. I wanted to let you all know that *#1 a few times did the trick in every case where we had this issue. Thank you all for your responses & Happy Holidays.

Thanks gentlemen! checked E600-E602 and they aren't pointing anywhere beyond the phone for any of the extensions - Just to clarify, I got back AB1 for A005 - according to my notes that's *#1 to clear, corect?

Howdy all, hopefully have a simple issue. I have several Dterms in a department with about a dozen users/phones. Recently one of these users attempted to forward all calls (user hadn't attempted this operation in about 6 months) and the phone screen stated Restricted - it had aparently never...

Ok, I first attempted to make the changes you suggested, which allowed me to connect but I couldn't get any traffic to pass. Next I opted to remove all of the remote access configuration and start from scratch using the ADSM wizard. This also allowed me to connect but not pass traffic. Here's...

Thank you. I'm going on site to do this today and will follow up.

Hello, I'm attempting to reconfigure an in-place ASA5505 to support both site-to-site VPNS (in place and working for some time) and remote access VPNs (where I'm stuck). The issue I'm running into is this - the VPN client connection will pass phase 1 and authenticate the user. Immediately...

They aren't, however I did manage to figure this one out. I made the configuration more concise, using the same crypto map for both types of connections and baom, they both came up without issue. Thank you for looking at my problem.

I hope this is simple. I have an established site-to-site VPN between an ASA5501 and an ASA5505 (5505 connects to 5510 using a dynamic IP configuration). I now need to add a remote access (Cisco client, using Xauth on the 5510) VPN configuration. I've done this successfully, however when the...

Thanks for the help. Before I started digging much more, I suggested to them that the current order was likely going to result in better outbound line access - they're going to leave the lines as they are. Thank you again for all the help!

ok: 8AA000>0>4005 8A4005>9>1007

Thanks again to both of you. mextera: I get A126, 02 (pickup group # and trunk number are both 02) and NONE in order of your question MercuryComm: All extensions are set to "02" which is the correct trunk number. Also, 3583>02 is set to "0". Could this be indicative of a hardware failure...

I spoke too soon and had to reset (darn). The user has the first to programmable keys on a Series i 16D programmed for each of the lines (D002 and D003). To make an outbound call as programmed, they pick upt the phone, dial 9 and the number. After pressing the 9, key 2 (D003) lights up. The...

Thanks to both of you - CMD 93 was the ticket!

I've got a situation where a client has a pickup group with 2 Centrex lines to themselves. The lines are assigned to two trunks (D003 and D004) and in turn to their pickup group (tenant 2). When calls come in, they'll successfully rollover from line 1 to line 2, however when they pick up to...

Thanks a ton, both of you - I feel alot better being able to extract some existing data first and seeing how the pattern will actually look. I'll let you kniow if I blow something up!

I've finally been able to get back to this project and I've run into a spot where I could break things if I'm not carefull. The CCIS trunks and routes are configured and now I'm getting into LCR and I'm fearfull of wrecking existing LCR patterns. There are development patterens already assigned...

Hey! That did it! Thanks again for all the help. This board is a life saver!

Ok, I'm going to try something. Right now, all three trunks are set to 3002/3>xxx>02 (trunk line appearance) - I'm going to change them to 3002/3>xxx>04 (direct-in termination). Can anyone see why I shouldn't try this?

Thanks for the replies. 1202 is set to 1515 (restriction class). I checked 1526-29. Class A for 209 is RC 15, which is set to ALLOW (1) in all 4. I couldn't find any Restriction Class-like configuration for trunks (excuse my ignorance if that's a known thing) so I'm stumped. Going to go back...

I've got 3 trunks (16, 17, 18) which are all ringing to an extension (209 - day and night). Originally they would stay ringing (3013/4/5/6>xx>15) however I've been asked to have them go to 209's VM. I've tried changing 3013/4/5/6 to 04/04/01/01 (ATCON) however it didn't change anything and the...