Search results for query: *

Hi all, We have a Mitel A-470 AIN set up.Both the systems(Master and Satellite) are on Release 4.1 HF4 .Earlier, whenever we had a network failure then the Satellite system would reboot automatically and would come up and show " Satellite in offline mode" on the display of Mitel A-470. Post this...

Hi all, I found resolution to the original issue that is i need to remove the numbers that are configured by default in digit barring option 1. Also the Basic function was set from All barred to All free.This resolved my issue. Thank you @sarond and @zoo1 as the things i learnt from you will...

Hi all, Thank you for various suggestions to resolve this issue.@zoo1, i tried taking a trace using Ttermpro(equivalent of Hyperterminal) by logging into port 1818 but iam getting these options as attached. Could you please guide me so as i can take the exact trace that is needed? @sarond,no...

Yes.I had removed and reconnected the PRI cable .That didn't work too.Since this is a dual T1/E1 card so I had connected to the second PRI port too but that too failed .PRI link is always up in any instance as incoming calls work srirammig112

Thanks for responding Sarond. No I did a standard reboot but that didn't help.So had to restore the previous day's back up. Regards srirammig112

Hi all, Request your help on this issue . I have been reported and i have personally noticed that the outgoing calls from ISDN PRI suddenly stops working automatically once in a while. At first i thought it was something related to the permission set but later found out its not. Here i have...

Dear all, Thank you so much for helping me out with your valuable suggestions and links. Iam now getting the raw data from Mitel which helps greatly. Thank you once again Regards srirammig112

Hi all, Request your help in resolving the SMDR issue in Mite A-470.I have programmed the settings in charges>general but can't get any raw data when i connect to Mitel A-470 using Tera term(equivalent of Hyperterminal).I type in the IP of Mitel and port no 1080 but not receiving any data. I...

Dear all, Thank you for helping me out. It was because of your suggestions the i was able to isolate the issue. It seems that the issue is with conference bridge service provider.I had tested by dialling into this conference bridge number from a different PBX system (Siemens Hipath 3550) and i...

Dear kwbMitel, When calling in from a cell phone and then muting it the calls doesn't disconnect . Thank you srirammig112

Dear Billz66, Thank you responding. This issue is happening only for outbound calls to the conference bridge.All other calls are working fine irrespective of turning on the mute key or not. We also observed that while being mute on a conference bridge call if we press any key then the call gets...

Hi all, We have a Mitel 3300 CX with rls 8.0 pr1 active sw load 14.0.0.91 .One PRI and 4 analog trunks . There are no issues of disconnection whatsoever for local or long distance calls. However, when we make a call to an International Conference Bridge (in UK) we observe disconnection of calls...

Dear Zoran(Zoo), Thank you so much for replying as always.We have set up AIN Master -Satellite and have defined all the settings in Master as well as Satellite as per the technical manual(i have enclosed this manual for reference).Calls are through between both systems now.As per manual, the...

[s]Hi, We have 2 Mitel MiVoice A-470 systems which we tried to network through AIN. The AIN along with expansion license has been applied on the Master system and we have configured the Master's IP on satellite system .We are facing an issue where we are not able to allot media resources (VoIP...

Yes, "Display Held Call ID on Transfer" is in fact enabled srirammig112

Thank you guys. I will try to convince the customer or rather educate him to accept this as a feature . srirammig112

Dear Nemmessis and kwbMitel, Thank you for responding. The first 3 party conference is done like this : First call>Transfer/Conf. key>second call by dialling 9 followed by the external party>Transfer/Conf. key This Transfer/Conf.key is the fixed key beside hold button on the phone. Are you...

Dear jpruder, If you know the solution then kindly provide .Its a request. srirammig112

Hi all, One of my customers while installing Mitel 3300 CX has asked us to disconnect the second incoming call to the operator(a 5360 IP phone).This is an ISDN PRI circuit and we have configured and assigned a welcome message to be heard on the main board number for an incoming call.Now if i...

Hi all, I have a Mitel 3300 CX ver 8.0 .Everything's been programmed according to customer's requirement.While testing the 8 party conference we have observed one strange issue. The issue is that while making the second call,where iam initiating conference from extn 7006 , the party says that...