Search results for query: *

NO. The last two ports of a 2 x 6 expansion card(s) is for Companion only.

All good suggestions. One detail I forgot to mention. I replaced the M7100 with an M7310. Verified that it maintained the same DN. The M7310 did not ring on an incoming. Replaced the M7100 and the ringing came back. Any more ideas?

My customer has a MICS 7.1. I have set all phones to appear only, with the M7100 courtesy phone set to NO line appearance. The voice mail is programmed to answer after 2 rings (to get the caller ID). The M7100 still rings for the 1st 2 incoming rings on all calls. I have made sure that there...

Ynotphone, You're absolutly correct. Got me to thinking, so I created 4 phantoem DNs and made the appropriate people answer DNs to the phantoems. Works like a charm.

Have a customer with 4 hunt groups on a o x 32 rev. 6.1xc. Incoming answered by a fibre NAM. CCR option 1 goes to hunt group 01 (707). CCR option 2 goes to hunt group 2 (708) etc. If no one answers the call just rings and rings. Why isen't it going to a mail box if unanswered? Several extentions...

Will a Flashtalk2 rev. 2.0 work on a 308 k.s.u. DR-5 (green label)?

Curly Cord Would you have an an idea as to where a fellow installer / programmer can get (or buy) the debug routine and codes?

Has anyone found a way to find a lost installers code on a BCM yet. The HEX code tables for MICS and CICS are invaluable, but can't find similar tips for BCM.

Found your problem. On a MICS in maintenance: modules 1 and 2 are the K.S.U. itself. The expansion begins at module 3. Therefore your expansion is module 3, 4, 5, 6, 7, and 8. i.e. - 6 ports. To go beyond you need a second expansion card. If there are 2 - 6 port expansion cards installed then...

The CICS comes with a built in auto attendant. It will not take messages, but it will answer and direct a call. Make sure this feature is turned off.

I'm assuming that you have 2 - 6 port expansion cards installed. I don't understand why you can't see ports 9 and 10, but remember that ports 11 and 12 are for companion only and can not be used for trunk or station modules.

NETWT, good question. Never thought to ask the volume of messages left. There's always Monday!

The customer is not sure if the've picked up a live call or not. I'm going to extend their rings before AA so they can answer all calls live as an experiment then will re-post the problem with a narrower field of description of problem. Thanks everyone for the help so far.

I have a client with an MICS rev. 5.0 and a Flashtalk2 rev 2.0.01. The volume on inbound calls is very low when it goes through the AA. I've changed the Caller I.D. cards and the voice mail. The volume directly on the underground is fine. Any ideas?

Thanks everyone for your suggestions. Solved it myself. FYI - Doorphone must be installed on main module. It will not work on expansion module.

Sorry. Part number is NT8B79FDE6. This is the BST doorphone (I am an authorized Nortel dealer, and the part was ordered new from the distributor). Why I can't get into the programming is the mystery.

Installed a doorphone on a BCM 50 rls3.1. New doorphone NT8B79FE6. Button on doorphone is lite, push button and you get tone in speaker. Cannot access programming (feature 9*4). It tells me "inactive feature". Go into maintenance and the port shows "idle", device says "doorphone". Dial the...

I check the VM DN. both the prime port (500) in this case and the second port. neither are in the ring group. Why does 221 ring once before the group starts ringing?

Have customer with MICS rev. 4.1 software. 29 telephones out of 48 are in ring group one for night ringing. in night mode the receptionist's (221) rings once before the ring starts. As the voice mail picks up after 3 rings, this only leaves 2 rings to grab it. I tried removeing 221 from the ring...

Rik. No DID, No call forward. If you call into the system, V/M answers, dial that ext. #, it rings just fine. Only on the ring group it refuses to ring.