Search results for query: *

Howdy Forum, Let me start by saying I'm a rookie in charge of an Avaya Definity G3si v.12. Our switch is shared to support 2 companies within the same bldg. I'm looking to take over the 2nd companies extensions and get outgoing commercial service. We currently have 2 ISDN lines and wanted to...

That was great. It worked for me too! My users are grateful. Thanks for the great tip!

Thanks guys. My DS1 is already configured, but I'm trying to test my end, but I type "test trunk 1" and I keep getting "out-of-service-NE". So I busy my DS1 board and "test ds1 01A15 ds1" and it fails test 1209 (no error code), and passes test 1210 and 1211. What does it mean when test 1209...

Sorry, I was in a rush when I posted earlier. I have a Definity G3 and the T1 is ISDN-PRI connecting to an MSL-100. Circuit pack is a TN464HP with 120A4 CSU. My distant end needs my circuit up, but I don't think I'm inputting the right commands (i.e. release board...). I "test ds1 01A15 cpe"...

I'm trying to enable a my new DS1 that's currently "out-of-service-NE". What's the command to enable the T1. I've tried "busy board 01A15" then "release board 01A15" but I when I do "status trunk 1" it still says "out-of-service-NE". How do I place my DS1 into service? Thanks.

Does the avaya loopback jack do this for me?

2BAvoice, do you mean connect the white orange pair to the "white blue" pair? Pins 1,2,4 & 5 are the orange and blue pairs? Is this what you mean? Pin 1 white orange to pin 4 blue Pin 2 orange to pin 5 white blue Thanks for you help...I really appreciate it.

Thanks TPhoneD. So my question is how to do a loop back? I know it's a stupid question, but I've never done this (just kind of given this new duty at the last minute). So how do I do a loop back test to isolate? Thanks.

Anybody there? :)

So does failure of test 138 mean it's on my side?

I did a "test board 01A15" and it failed test 138, but it passed the rest. Here's the results: Port Maint Name Test No. Result 01A15 UDS1-BD 138 FAIL 01A15 UDS1-BD 139 PASS 01A15 UDS1-BD 140 PASS 01A15 UDS1-BD 141...

Did this DS1 ever work out for you? If so, what protocol version did you use? I noticed you have it set to "a", but I thought Nortel uses protocol "b". Just curious since, I'm also trying to connect my Avaya Definity to a Nortel MSL-100.

I thought there was something I had to do with the CSU or loopback cable to loop the signal back on my side? I did a "test trunk 1" and the following came back Port: 01A15xx Maint name: ISDN-TRK Alt name: 01/xx Test No.: 36 Result: PASS Error Code: Test No.: 255 Result: FAIL Error Code: 8...

I'm trying to install a new DS1 ISDN-PRI trunk using a TN464HP circuit pack. I've done all the configurations and the circuit path is good, but when I status the trunk, I get "out-of-service-NE". My distant end will be a Nortel MSL-100 (still waiting for technician to connect his end), but...

My Definity G3siV12 is an hour off. How can I change the time or enable Daylight-Saving-Time? I "displayed time" and it looks like DST is not enabled. I tried "change time" but a list comes up that I'm not prepared to change. Any info is appreciated. Thanks. -Peter

How come I can't change the date interval on my ASA? I'm trying to pull Trunk and Call Traffic info but it's not allowing me to change the date. It's stuck on one day time period. I can drop down the calendar, but it won't let me select any other day. Thanks.

Our e-cas computer has been disconnect for months now, and I'm trying to get it back online. It was working at one time, however these people relocated the e-cas PC and since then it hasn't been able to connect. I found the jack it was plugged into, and traced it all the way back to a...

The only time we use craftppp is for voicemail. There hasn't been a technician out here. Is there any where I can enable it?

Thanks 98Converter! It no longer states: ***Busied out resource detected; verify if release is needed It turns out I needed to release MIS. however it still says: Alarm origination is currently disabled What's that?

Whenever I logoff, I get this message: Alarm origination is currently disabled ***Busied out resource detected; verify if release is needed Any ideas. Thanks.