Search results for query: *

cool, I will look into... THX

Hello, I currently have a successful PRI Trunk connecting to a Gateway device... I currently run a hybrid system, asterisk PBX and an Option 11c... I wanted to see how I could access paging across this PRI... I currently can cross communicate to 2616 / 500 sets directly with DIDs but trying...

Thanks for the reply guys(assuming guys sorry if not)! I believe that the TMDI DCH will have issues if I enable ISDN YES, after review I think that it is due to my current release... If I could update release then I could utilize TMDI DChannel for PRI but since that is not an option I have to...

I have an Option 11C and trying to do some testing without "outing" my current trunk to test another trunk via DCH with MSDL... I believe in the past, I would have to alter the CDB to "ISDN YES" in order to use the MSDL capability... In turn this would cause issues with the TMDI card and the...

Hello, It was something related to my gateway device... I didnt have it properly routed...

I have it set to that...

Outed trunks errored trying to get new to TIE... (route confict type) tried to change RDB from did to TIE, unable to change route of trunk error sch3146. i will have to try to out route and rebuild on off time... But is there anything we can tell from the trunk setup? TYPE DID CUST 0 TRK...

Could there an EM wnk signal I'm missing? Like a polarity switch in the gateway device? With my setup there should I hear dialtone on trunk TN?

I don't hear anything, not sure if I'm not provided dialtone... I have a gateway device providing the trunk... Like stated, I get calls thru but not sure if I have route setup right for outbound...

Hello I'm not getting dialtone when dialing my ACOD for trunk... External dialing basically, this is in association with dialing a 9... I have monkeyed around trying to bring up a failed pri converting back to DTI... I am receiving Inbound calls on trunk but unable to make outbound...

10:4! Is there a non evaisive way to allow Direct DN dial on the route? I was assuming that you have to disable IDC on route to acheive this...

Hello, Its been a while but still running my Option 11c... This may be a silly questions but is there anyway to have a channel/channels pri(23) go to different route? looking to do some testing and currently using gateway device to intercept telco PRI... I'm successful passing calls through to...

Thanks! I think that puts me in the right direction! It's amazing how many complaints you get when someone has to dial an extra digit... I guess most people don't like change...

Wow, great information I'll give it a try thanks.

Hello, Anyway to configure DID fax to skip AC1 (Dial 9 for outside line)? I've read about Pre-translation tables but unsure on the best route for this... Could someone give me some guidance on this... Thanks!

Sorry, that is my current DTI Route... This is the PRI Route... REQ: prt TYPE: rdb CUST 0 ROUT 0 TYPE RDB CUST 00 DMOD ROUT 0 DES TWTELCOROUTE TKTP DID SAT NO RCLS EXT DTRK YES BRIP NO DGTP PRI ISDN YES MODE PRA IFC NI2 CBCR NO NCOS 0 SBN NO NCNA...

So here is my NXX: [highlight #FCE94F]REQ prt CUST 0 FEAT net TRAN ac1 TYPE nxx[/highlight] NXX 704 [highlight #FCE94F]NXX 704 RLI 2 SDRR NONE ITEI NONE [/highlight] NPA 1704: [highlight #FCE94F]NPA 1704 RLI 4 DENY 976 SDRR DENY CODES = 1 ITEI NONE [/highlight] And here is my...

Hello, I was able to change the number being passed off to the Telco company... It worked!!! I think BARS is restricting me some how... I can make an outbound call using my ACOD but when I dial a 9 and my local area code I get a busy signal... Is there something with my AC1 and NPA for my...

Great! I will give it a shot! Thanks for all the help!

Actually I was able to get in touch with the telco and they stated that the call would go through but "5100" is the DN or Extention from the phone I'm using... How to I change that to pass my external number that they are familiar with? For instance: CALLING #:[highlight...