Search results for query: *

Has anyone ever experienced an issue with HP BL460C G5 placed into a C7000 chassis where you shutdown a server and it immediately reboots itself. I have sniffed all network connections looking for WOL protocol and I see none. Is there a setting somewhere that allows this to happen within the...

Thanks for you reply brianinms. Any issues with horse power on a device with 2mb of memory. Additionally adding two site to site vpn tunnels? Thanks, V

Common Access Card Thanks

If anyone could point me in the right direction here. I am wondering if you can have an ASA5500 sw version 8 have both CaC and non Cac access via VPN client. Any insight would be appreciated. Thanks,

Does anyone happen to know or point me in the right direction in finding out if a Cisco ASA5500 series appliance can do both CaC and non CaC authentication on the same unit?

I recently did a show controllers Ethernet-controllers gig command on an access switch to monitor and gather data on an gig link to my core switch. When I look over the returned data accumulated I see the transmit and receive bytes go up and down but frame counts steadily increase. What is this...

Thanks works great now.

I am getting ready to deploy Windows 7 across my mostly Catalyst network. Mostly Cat Switch (6509) Core and 3550’s and Foundry 10/100 with Gig links on the edge. This is all going across via multicast and I was wandering how I could tell if I am going to saturate my network connections and how...

I have a old Cat5K running to a cat2900 via 100MB Multimode fiber. I am seeing a lot of collisions and runt frames on the link which additioanlly reports very slow Internet access times. This link is set to half duplex and the distance seems to be within 400 meters. What are the usual suspects...

Thanks for your response. I have sshe enabled on my vty ports with a rsa ket enabled. The vlan I want to block this traffic on is on a vlan which faces the public. It has a web server on it along with a few other devices offering services to the public. I am trying to block ssh telnet etc from...

I have a cat6500 running IOS and have a public facing vlan. This vlan has my web server hanging off of it. I need to block using an ACL ssh and other management traffic but allow all other traffic in. Can I get some assistance on setting up an inbound ACL to block this type of traffic. I have...

Does anyone know how I can confirm the circuit and bandwidth my carrier has provided. I kind of remember a formula you could use based on ping response and packet size. Any help would be great.

I have a monitor session setup on a copper port looking at all my vlan's configured within my 6509. Is there any particular vlan my siffer needs to setup for or can I just setup up the destination port with a single switchport command and assign the pc a static vlan 1 ip address. I do not use...

If anyone can answer this, I just disabled the ipv6 scope on my dhcp server and as a result the server no longer displays an running status. My ipv4 scopes do show active and everything appears normal. Would I expect to see this? Prior to doing this the server always showed a running status...

Layer 3 is what I need. Thanks V

I need to see about replacing a Cisco 3550 (Cisco 3550-12G, multi and single mode fiber)with a new model Cisco switch. Can someone make a suggestion on a comparable good replacement Cisco switch? Thanks for your help. V

I have a Cisco 6500 with s222-ipservicesk9_wan-mz.122-18.SXF17.bin code. I am trying connect 3750G's in a stack and bond two gig interfaces together. Additionally I am using dot1q trunks on the gig interfaces. The 6509 card I am connecting to is ws-x-6416-GE-MT. PVST spanning tree on both. The...

I have a Cisco CBS 3020 in a HP array which I can not manage vis ssh ver 2. Compapred to its twin the configuration is almost identical with the exceptions of some access port vlan allocations. i have zeroed out the rsa keys regenerated them etc. My problem is I have no experiance with this...

Thanks for the input. It looks like I am running IOS on the switch side and I am unable to session to the msfc card. My understanding is the switch was recently updated with new IOS. i can boot the switch from rommon via the boot cmd. Code level 12.1(27b)E4. Here's what I see after issuing the...

I have a Cat6500 with Sup2's on 12.1 code. It has been a while so I was wandering if someone could explain to me the way in which this device routes Vlans. Looking at the IOS I do not see the classic routing setup and since it has been a long time since I have touched one I do not if you have to...