Search results for query: *

Ok, I finally got it to work. Perseverance paid off. :) Here is the final config for documentation purposes of others that struggled like me. No, I do not know what the final steps that made it work, part of it was reconfiguring my firewall (Watchguard XTM 22). hostname "LAR1-CORE"...

ok, got the new switch, fresh clean config. Loaded up the following: ip routing vlan 1 name "DEFAULT_VLAN" untagged 49-52 ip address dhcp-bootp no untagged 1-48 exit vlan 36 name "Voice" untagged 1-48 qos priority 7 ip address 192.168.7.2 255.255.255.0 tagged 50...

I've got a brand new HP Procurve 2620 POE switch showing up today. Once I get that in, we will know a few new things. 1) Does this LLDP-MED stuff only work with a POE switch 2) will a new switch (NON POE) work? I have a 2 new 2910al's in for a different project. Since it would have the...

So, the firmware for each of my test switches are at the latest that HP provides. There are two switches I have been playing with: 2824 (j4903a) - i.10.77 released 08/26/09 https://h10145.www1.hp.com/downloads/SoftwareReleases.aspx?ProductNumber=J4903A 2810 (j9021a) - n.11.52 released...

SCCP 8-5-2-SR15 I think I read somewhere that version 8.3 or better was needed.

Thanks Vince, thanks Cajun. Yea, that document I came across a while back. I think my problem is partly stemming from the cisco phone will not pick up the DHCP address associated withthe voice network. LLDP-MED is enabled on the phone, and I have obviously designated the "voice" parameter on...

So I added the switch into the mix this morning. I'm using a 24 port (Procurve 2810) and am only using a small subset of the switch for testing. Ports 13 through 20 specifically. For now, lets just ignore everything else. vlan 1 name "data" no ip address tagged 13-20 qos priority...

Ok, just another update before I head to the house for the day. I went back into the firewall (Router), changed what I want to be the "Voice" VLAN to UNtagged, and the data to tagged. Now when the phone boots, it grabs a Voice VLAN IP address, 192.168.7.101 (instead of the data one). I...

Ok, router (Watchguard Firewall) supports vlans, I'm just diving into new territory here, so this will take me a bit of time to figure out. I got two vlans defined on the port (just like the switch config above). I re-defined my VPN tunnel on both sides, Corporate and remote site (It's good to...

From re-reading through what I wrote, and reading a few other docs, I cannot have two ports untagged at the same time. So, with that in mind, the config would look like this: ip default-gateway 192.168.6.1 ip routing ip route 0.0.0.0 0.0.0.0 192.168.6.1 (or would this be 192.168.7.254?) vlan 1...

Thanks for the post back VinceWhirlwind. So, if I am adding back in 49-52 as tagged on each vlan so it can propagate out, then I would change the Voice VLAN to untagged (like in the example below), or would I just have tagged 1-52 instead? ip default-gateway 192.168.6.254 ip routing ip route...

Hey folks, New to this board. I did do a bit of searching, read through this article (http://www.tek-tips.com/viewthread.cfm?qid=1656061 which VinceWhirlewind had some good insight). I am new to the HP world (Mostly light Ciscoing) so my questions may sound incorrect. Also, I inherited this...