Search results for query: *

The SBC is my gateway to government telephone network and my Avaya CM is not encrypting with them but with softswitch at other end of the SBC network. The SBCs are basically set to transparent to allow my CM to do the encryption instead of the SBC. It's a government requirement that the CM be...

I have been trying to get SRTP media encryption to work on my SIP trunk connecting my Avaya Aura CM 6.0 to an ACME Packet Session Boarder Controller (SBC) managed by another agency. They configured the connection on the SBC red side as transparent to allow the CM to do the encryption. I've set...

Awesome. That's what I did; leave em blank. Thanks for the tips.

Thank you lopes1211. Do I need to change anything on the Mode and Type for each channel used? Mode options are e&m, protected, and simplex; Type options are t1-comp, t1-stan, t5-rev, and type-5. I ask, because the far end indicates they have DIOD on all channels (Dial in and out). The only...

Thanks. Does give you various options, just not what I was looking for to connect with the other end. I'm thinking I'm better off opening ticket with Avaya Support to see what they say.

Thank you kyle555 The other end tells me they are set for channelized ESF B8ZS T1 using only 5 channels. They are utilizing CAS with Immediate start and are set for DIOD on all channel. I'm finding that when i add ds1 the CAS setting will not allow 1.544, but only allow 2.048. My Avaya will not...

Hi folks, I need some help with some steps to setup a non-ISDN T1 trunk on my Avaya Aura CM using MG450. The trunk is to connect to a customer PBX to allow a channelized trunk to pass 3khz voice lines to use my switch as a gateway to place external calls. I tried setting up a ISDN PRI, but it...

I know I can program a autodial to an external commercial number, but is there anyway to have commercial numbers show as bridge appearance for incoming calls? I am trying to work something out for our Fire Department where their dispatch can receive incoming calls on a commercial number they...

Thank you for you all responses. You've been helpful. Just confirmed my suspicion.

Have a customer complaining of call drop outs and seems to be the only customer from his building complaining. His VoIP phone shows in-service and I monitored his call all day. I did a list trace station xxxx for his number and show good call activity. Might see a little jitter every now and...

Anybody know what this event means and if there is a fix on the switch or is this something external like from the network?

Thanks for your inputs. I created the coverage path pointing to the hunt group in each coverage point (all six), and added that coverage path to the hunt group set up as circular type, and in each of the stations. It works well up to the sixth point, then returns to the first number in the...

Regarding thread690-1670813, after you enable Station Hunt Before Coverage in system-parameter coverage-forwarding, How do you configure the stations to hunt in a chain? I have three stations in a coverage path, and the call always stays ringing on the last station. If I add the first number...

Thanks Kyle. Never even bothered to look at that. Still have a lot to learn.

Regarding my last I figured out my error. I had to take out the Coverage path between 0700 and 1700, and left the Sunday and Saturday as all 00:00 time. My only question is with Sunday and Saturdays as 0 hours to the coverage path, will calls stay covered to go off-net from Friday 1700 until...

I have the same problem, I need to enable SRTP, but I have checked display system-parameters customer-options and found Media Encryption Over IP? set to n. I read a document, Configuring Avaya CM for Media Encryption Issue 1.0, and it indicates that if the Media Encryption feature is not...

Hello DJK205, I created a Coverage Path 11 and under coverage criteria I set to "y" ALL, DND/SAC/Goto, and Holiday Coverage; and Point1 set to the existing VDN that I have been using. Then I created the Time-Of-Day Coverage table as follows: TIME OF DAY COVERAGE TABLE: 6 Act Cvg Act Cvg Act...

I administer a Avaya Aura CM 6.0 and I have been trying for the longest to figure out how to program the system to automatically set Call Forward Off-Net for a specific extension after working hours. Has anybody done this that can point me in the right direction? That is, assuming that the...

Having problems configuring an Ultratec Uniphone Combination TTY and Telephone device for a customer that has an employee with hearing impairment. Configured the line as analog since the device connects via regular 2-wire analog line according to the manual. Has anybody out there been...

Appreciate everyone's response. I discovered that my VoIP telephone DHCP server is the HTTP Server. The configurations that TELECOMSONATRACH told me to check match with the exception of: params=/usr/bin/snmpget which on my server is set for params=-v2c-cpublic. Also, I could not find MV_IPTEL...