Search results for query: *

I think what I am going to do is to create some sip lines and have them assign me a did and add it into the mix but then add a short code that will allow me to test outgoing and incoming calls while allowing them to continue to use the existing analog circuits. Once I have tested and feel like...

Like the title says I have a small business that I have upgraded to 11.0 version and purchased SIP trunk licenses and looking for best way to migrate the service from our existing analog lines. Currently we have about 4 ananlong circuits that act as trunks with 2 inbound DID's for different...

Thanks for all the suggestions!

Yeah sorry, I am located in the US, I was originally looking at flowroute but started seeing that support had gone downhill since they have been sold etc...voip.ms from what I have read is a mixed bag. For me it's not about the lowest cost, its more about support and reliability, if I do have...

Understand, I was just trying to see who folks were using provider wise that were providing reliable service and responsive support, etc...

Skyetel was one of the ones on our list, but was just trying to see who other folks were using and how good the reliability and support was...

Just wondering what are folks using today that works well with IP Office. I have a small church that want to move from analog lines(4) to SIP trunking. Would like to go with a per minute provider since they do not use many minutes, pretty simple setup. Not looking for necessarily the cheapest...

There are 2 echo settings echo cancellation and echo reduction, did you turn both of those off? Thanks

Understand and appreciate the input, I will be on site this weekend and make sure the ground is good and run the impedance tool manually on each line

The cabinet that its in is properly grounded, I am pretty anal about that stuff but I do not have a connection from the grounding lug to the cabinet, I can do that but im sure if I metered it out I would see that it is grounded properly since its connected to the cabinet rails to the chassis but...

I know, I know we are in the process of migrating to SIP trunk but I needed to upgrade in order to be able to purchase the SIP trunk licenses. We upgraded from 8.0 to 11.o and that seemed to go well, no major issues but I have users now complaining about echo where they were fine before. We have...

They are running embedded voicemail as far as I know, that is a good question it appears that the consensus is 11.0 is much more stable than 11.1, is there any version of 11.1 that most feel is stable or should I just avoid 11.1?

Yup my question is I need to replace the 4g Avaya SD card with an 8G Avaya SD card and trying to figure out when to do that, I have read that sometimes the older 4g cards cause some issues. So do I swap out the card in the beginning or after upgrading to 8.1.95 etc...The other thing is I have 2...

I am working on the steps for upgrading an v2 system from r8 to r11.1, I know I will need to make a step upgrade to update the bootloader and have the basic steps outlined, here is what I am working on steps wise, system is running all 96xx phones about 33 endpoints, no voicemail pro, essential...

I am trying to get some recommendations for vendors in the St. Louis area that can upgrade software for an IP office system. Currently we have analog trunks and would like to migrate to SIP trunks but cannot purchase the licenses since our software versions are no longer supported. I have looked...

After doing a lot of reading on the installation and how things works I think I have a much better understanding about how it all works. The sad part is that it appears that who the church paid to do the installation did a very poor job and the phone system is actually mis-configured, its a...

The phone hits bothe the upgrade and settings bits, and continues to the extension part. What I do not see if the phone has upgraded the firmware. If I look at the phone itself its still running and older version of firmware then whats called out in the in the 96Hupgrade file. I did a factory...

Yeah I assumed that to be the case but is there a way I can go to the directory via a web browser. If I go to the base URL it comes up with the status page, if I put in the settings file or the upgrade I can have those displayed. But if I put in the .tar files, and maybe I am using the wrong...

I have a IPoffice that I inherited from a phone company installation, I think I have most things mapped out but still coming up to speed on how everything works. We have 96xx phones, running 6.2.4 but from going through everything I do not see a http server setup. The reason I ask is I have...

Yeah it doesnt get to the point where I can do that, it seems like the firmware is bad, it doesn't completely boot up and make it to the screen where you can do #craft, it get stuck on the initial boot screen and none of the buttons do anything. Would really like to know how to reflash the...