Search results for query: *

Try :_ LTMG A this gives all Trunk Main groups look for a MG with a table number under 'DDT or DTT' then list these tables by 'LDTT x' you may well see something like 599 4227. it could be you are receiving 4 digits to translate to 4 digits, you have to work it out or paste on this page. Mal.

25 pin to 9 pin lead from Maplin:- http://www.maplin.co.uk/p/serial-rs232-25-pin-male-to-9-pin-female-3m-l69bt £2.41p If you have not got a 9 pin serial socket on the PC then you will also need a usb to 9 pin convertor. £8 Amazon. Better than messing about with pin outs... Mal. Latest...

Never done it, but this is from the book.... Dial the messengers hunt group number When the machine answers key 0 # “system administration prompt” Enter the security code followed by # “menu options played” Though it is not an option on the menu now press 9 “ a warning is now...

I found this on the web.... http://www.pagematic.com/faq/ws_ftp.html Mal. Latest Manuals:- http://www.siemens-enterprisehipathdx.com/hipathdxeps7/

WS_FTP95 is an old program and available on the net. WS_FTP95 is an excellent FTP (file transfer protocol) program, it is what most Siemens/Realitis/iSDX engineers use. each site with its own IP address or if stand alone using a cross over 88.0.0.1/2. Under profile ( Name) Host type Auto or...

I forgot to say, use the CLI based routing to sent the call to a invalid extension number to give NU. Mal. Latest Manuals:- http://www.siemens-enterprisehipathdx.com/hipathdxeps7/

CLI (Call Line Identity) based routing is possible on Version 8 appack 3 or later, I have never used it but the commands are:- ACBT (Add to CLI based routing table), DCBT (Delete from CLI based routing table) LCBT (List CLI based routing table). You could play around to try it using a known...

The only ALI Card (Analogue Line Interface) that will fit into a micro is a 1HAC50066, and I seen to remember it can only go in either slot13/14, the same a a DLI, the filter is a 871/1/06820/xxx. A very rare card to find. Good luck, Mal.

Command 'bye' only stops the terminal been used by anyone else, the port is still open and you can sign directly on again, it was used when terminals were located next to the equipment to stop 'finger pokers' playing. When using Telnet or a modem the program been used has a 'hang up' command...

not unless you know someone with a copy 4.8 is the version to have, it quite old (1999) so there must be copies out there, its also the program most Siemens engineers use. I have found this on the web:- http://www.egydown.com/gx/Symantec+Procomm+Plus+4.8.html I also found this on a Torrent...

I have only come across this when the telnet program has been closed, i.e. not using the disconnect first, what are you using for telnet? I always found that Procomm Plus was the best allrounder for accessing switches of all types using dialup/telnet or ftp, it can be set up with individual...

MrWhisper, the "snmp.ini" file needs to have SNMP Manager reporting IP addresses in it which looks lik this:- [section_1] snmp_agent_status=ON ; Dictates whether agent will load dx_type=Realitis_DX ; Type of switch being managed get_request_community=public ; password used in GET...

Stoney, As far as I know it can only deliver in the format of the SNMP.ini file. And you need a MIB browser to read it, all it does is automatically report alarms to a central point, then the MIB browser (with the Siemens script in it) interagates the type of alarm, frequency etc... with the...

My attatchments did not seem to work, Here they are in full. [section_1] snmp_agent_status=ON ; Dictates whether agent will load dx_type=Realitis_DX ; Type of switch being managed get_request_community=public ; password used in GET REQUEST packets set_request_community=private ...

I have only done this once on a large public network. Attached are a SNMP.ini file which needs to be telneted onto the switch, there is a snmp MIB attachment which has to be configured into the MIB Browser. And a discription from siemens. I hope this helps.

System Filter Card faulty, very unlikely. probably the wrong cable, or are you fitting the berg correctly in the right position, P1 P1-1, P1-2, P1-3, (as the drawing) also I have seen these plugs put in upside down. FTP:- If you can FTP to the switch and open the files, you should be able to...

I was assuming your system was fitted rack mount with all the panels fitted, if this was the case there would be a maintenance panel in the rack looking something like this:- http://hipath.custhelp.com/DX_files/HiPath_DX_EP_V9new/EP%20v9.0/equipment/patch_panels/patch_gen_pur_1han50015aaa.htm...

DXR Port on the Maintenance panal are exacly the same as any DX, standard speed set is 9600 baud, sttings 8 n 1, but this can be altered. If you can log on via telnet you can check this by typing LSPS A , this will list the speeds of all the ports, port 1 is the maintenance port, port 4 is the...

SirCris, Here is a link on configuring a westell to Cisco, I have foud them nearly all the same to any small Data/Voice box. http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/pbx/interop/notes/481743nt.pdf Here is one on Ebay...

SirCris, One more point, You can use a IQ2000 Westell convertor to convert DPNSS to Qsig, this is nomally is used DX - Westell - Cisco routers, which provides a IP solution but with all the Dial piers ( Dial codes) been in the router. These are also used to connect a DX with Cisco Call...