Search results for query: *

I am trying to mirror an existing up and running netscreen onto a lab environment netscreen in order to work on getting tunnels up and running. Is it possible to cut and paste the encrypted VPN preshare key? for example, I can cut and paste a cisco hash into a new config and it preserves the...

Thanks. I was able to procure it legally without incurring any charges.

advanced security IOS. I assume this is something you have to pay cisco a million dollars for?

this is all I get.. what gives? Router(config)#cry Router(config)#crypto ? ca Certification authority engine Enter a crypto engine configurable menu key Long term key operations pki Public Key components provisioning Secure Device Provisioning...

Changed e0/24 to port-type nni and could ping it with ethernet configured in the subnet range, and still browse the internet with a ppp session on a different network.

what I can do is plug a synced up DSL modem into port 24, and my laptop into port 1. the laptop is provisioned as 10.137.32.146 255.255.255.240. I can authenticate a PPPOE session from my laptop to the internet and browse, but I cant ping my switch. The end goal here is to serve some...

When I configure my laptop to 10.137.32.146 and plug into int fa0/1, why can I communicate to whatever is plugged into 0/24, but cant ping the vlan ip address of .157? vlan 999 uni-vlan community name Management_VLAN ! ! ! interface FastEthernet0/1 description ADTRAN...

for the next noob that comes around, I discovered: autoconfigure takes fe80 and adds it to the front of the mac address of the NIC (plus some filler in the mac address part) if you get assigned a block of addresses, they get pasted on where fe80 goes and it becomes globally unique...

I have some IPv6 addresses I can use to get out to the internet, and I am trying to configure routing between two interfaces on a cisco 1841. interface FastEthernet0/1/0 description IPV6 TEST PORT no ip address ip nat inside ip virtual-reassembly duplex auto speed auto ipv6 address...

Transmission engineer says t1 ports are for TNE modems and I will never be able to uplink to them, even though the documentation says uplink ports.

show int desc says multilink is down. I guess the far end would have to be configured for multilink too, which isnt possible on this equipment. I wonder if it speaks HDLC?

here are the relevant portions of the config controller T1 0/0/0 cablelength long 0db channel-group 0 timeslots 1-24 ! controller T1 0/0/1 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! interface Multilink1 ip address 192.168.254.193 255.255.255.192 no ip redirects no ip...

I am working on a lab environment where I want to connect a router to a zhone Dslam through a t1 link. is ppp the correct encapsulation, or should I use Frame relay? When I bring up the t1 controllers, it wont activate the serial interface unless I issue the channel-group x timeslots 1-24...

OK, I went through my stack of old gear and found one with a Packet Voice DSP Module. I put an FXO in slot 0 and an FXS in slot 1, show run and boot-start-marker boot-end-marker ! ! no aaa new-model voice-card 0 ! voice-card 1 ! ip cef very excited. The first thing I would like to do...

I have 2 1760s with [2] vic 2FXO cards in one and [2] vicFXS cards in the other. How do I enable the cards so I can see them in show run?

Thanks, just got it going. After migrating, I used the existing ARID, and upgraded to 4.2. I set mytai/tapi to yes and networking to yes in the licensing and options form. Everything seems to be running smoothly.

Does that migrate the DB?

Software assurance is active so I will try to use existing. I don't know how to migrate the DB though.

Thanks I have read through it and have a few more questions. I see the command to do a database check before migrating the database, but I am not clear on how to actually migrate the database. Will it be a part of the upgrade software that will occur as I am running the upgrade software...

The upgrade to 4.0 went very nicely. thanks. where can I find something to read about the rest of the process?