Search results for query: *

Currently our organization has an Exhcnage server 2007 enviroment, so i descided that we are going to do a migration to exchange 2013. Everything has went as directed with the co-existed enviroment up until a user that has been migrated from 2007 to 2013 tries to login to OWA. When the user...

If it is not broke don't reboot it.... is my method.

I have an ASA 5520 that i am installing on an internal network. Using the network 10.36.56.0/21 as my example. I want the traffic to pass through the ASA keeping the same internal address on the LAN. would the following static NAT command allow me to NAT the entire subnet? static...

You will have to bear with me as its been a while sine i have setup L3 on a switch (5 years). I am workingg with a 4506-E with a 6l-e sup. I have nothing hooked to the switch at the moment. When i isses the ip routing command it takes the command but does not place it in the running-config...

We have 2 sups and 5 blades here is a show power: Supply Model No Type Status Sensor Status ------ ---------------- --------- ----------- ------- ------- PS1 PWR-C45-2800AC AC 2800W good good good PS2 PWR-C45-2800AC AC 2800W bad/off...

I have a 4510R with redun. power supplies (2800 watts) both connected to an APC UPS. Well over the night our APC died. Problem is i only have 1 240 30 amp plug to run off of until the new UPS arrives. Will there be any problem only running the 4510 off 1 power supply? It seems to be running ok...

I keep the same mind set as you Vince, some of these switches have been up and running for well over two years with no issues. So i am having a hard time talking myself into these upgrades being needed. The only thing that is pushing me towards doing it would be the security of getting ride of...

Do you see any problems with upgrading all of these switches through the Cisco Network Assistant tool?

We currently have 28 Cisco 3560-48PS switches running IOS 12.(25)SEE3-IP-BASE. We recently had to open a TAC case on one of them, and through discussion with the Cisco tech, he recommended upgrading all of these switches IOS to version 12.2(55)SE5-IP-BASE-CRYPTO as the version that is running on...

It sounds like you need to run the mutiple display wizard either from windows or from your video card configuration software. That way you can set your two displays up in "clone" mode and they can both work at the same time.

I use a 2811 as a CUBE, but you will have to make sure the IOS supports it.

I installed a Cisco 4510R switch into our datacenter a little over 4 years ago. As you can see by the picture I have attached, the switch has never been powered cycled since its install. The only thing that has been done to the switch every now and again I’ll swap SUP engines, but that has not...

The way i have it sent up with outbound calling i have one trunk tied to an outbond route with the following info: Outgoing settings host=XXXXXXXXXXXXXXXX type=friend dtmfmode=rtp-nte allow=ulaw canreinvite=no nat=no insecure=very qualify=no reinvite=no disallow=all externip=XXXXXXXXXXXXXXX...

Post a scrubed config of the outbound SIP trunk from the Asterisk server.

To use SIP trunks you will need a CUBE or an Asterisk server for the trunks to terminate to. If you use a CUBE it will need to support SIP inspection to correct your internal to external ip problem. If you use Asterisk you will need to make sure the NAT config is correct. 9 times out of 10 no...

Topology: PSTN>>>>>SIP Trunk>>>>>CUBE>>>>Call Manger>>>>>>AA When someone calls a DID that is pointed to an AA, the caller can pick an option off the menue and the AA will route the call to that ext. When the receiving EXT recieves the call it go straight to dead air. If you call a DID on the...

I have two networks attached to a Cisco 2811, 10.36.0.0 and 24.154.0.0. Currently i have the gateway of last resort set to the 10 network. With the last resort being set to the 10 netowrk the 24 netowrk is not reachable. If i change the last resort route to the 24 network it begins to work and...

Is there a methode using a translation or transformation pattern to where when a user dials example 5551234 the CUCM can insert the area code before it send it to the carrier? Currently the user will dial 8 to go out the PRI so: 85551234 so in the end i would like the carrier to receive...

Currently my company has been given 2 SIP trunks (inbound & outbound) as a promo from a local cable service provider for us to do some testing and consideration of a switch from the PRI. We currently have CUCM-BE Ver. 7.1.5 and a 2811 VGWR cable of acting as a CUBE for the trunks. What I need...

Based on the little information given.... no you can have two PRIs on one CCM.