I just got a new customer who inherited an older Mics with T1(the original) software, and a 4- port copper Nam. I wiped out the info on the voicemail,and pperformed a startup, now I can not get anywhere with F983. "Password invalid".I was able to get into F983 b4 I initialized the system.Tried the F985...9 thing, and no go. Need help on this one guys...Mike
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Nam password 1
- Thread starter mass1954
- Start date
Dmacnumberfour
Vendor
mass1954,
After you did the reinstall on the NAM you should have to enter 266344 and this will let you setup the NAM with the language and the Glists and a few other things and it will configure and then you use the F 983. It should be ready to go.You can then reprogram it.
Dmac,
After you did the reinstall on the NAM you should have to enter 266344 and this will let you setup the NAM with the language and the Glists and a few other things and it will configure and then you use the F 983. It should be ready to go.You can then reprogram it.
Dmac,
- Thread starter
- #3
- Thread starter
- #5
- Thread starter
- #8
WHAT?
if you are able to do a f985-9, then you have not re-installed. If it was looking for the config password, feat985 would bring up "inactive".
You need to enter the sysadmin mbx password or call a vendor.
I doubt you "have done this many times b4" as you say.
hmm let me try a crack at this.
Shut off your VM.. run your XFtest, because if you have the NAM on you can remove the darn feature codes, reboot the NAM, then do a feature 9*1, this will tell you all the feature codes being used by the NAM. If the Sys Coor access is another code, use that to prog. If you still cant get into the NAM... Tell your customer to call his vendor.
Nam555
Shut off your VM.. run your XFtest, because if you have the NAM on you can remove the darn feature codes, reboot the NAM, then do a feature 9*1, this will tell you all the feature codes being used by the NAM. If the Sys Coor access is another code, use that to prog. If you still cant get into the NAM... Tell your customer to call his vendor.
Nam555
- Thread starter
- #13
- Thread starter
- #14
No luck. I do f983 1020000, invalid. Try a reset sys pasword and it won't reset.Strange thing though, in f982 where it asks for the ext for the operator, it will only take 2 digets. Took the Nam back to the shop and will try and figure out why this thing is giving me such a hard time.Any other ideas will certainly help...Mike
ThePhoneGURU
Technical User
Did you try to do an xftest first on the KSU?
- Thread starter
- #17
-
1
- #18
westcoaster
Technical User
take the nam and place it on a system with two digit dn's and then try your f983 it should work then.....
Some people are like slinkies...not really good for anything, but seeing one tumble down the stairs makes you smile!
Some people are like slinkies...not really good for anything, but seeing one tumble down the stairs makes you smile!
- Thread starter
- #19
curlycord
Programmer
1. Can you tell us how you wiped out everything?
And to verify is F983 is asking you for Password or Log?
2. Log= 120000
or Password= 266344 (nothing to do with Config on KSU as nortechie suggested)
3. When you tried the 2 digit thing did you try it on the existing KSU or another one?
4. F915 sometimes rides on 916, 917 or 918 instead of 915.
And to verify is F983 is asking you for Password or Log?
2. Log= 120000
or Password= 266344 (nothing to do with Config on KSU as nortechie suggested)
3. When you tried the 2 digit thing did you try it on the existing KSU or another one?
4. F915 sometimes rides on 916, 917 or 918 instead of 915.
- Status
Similar threads
- Locked
- Question
- Locked
- Question