Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

1603/1608/1616 Mute commands have changed in firmware 1.330D 3

Status
Not open for further replies.
Bas1234

Bas1234

Technical User
Dec 10, 2007
6,760
NL
Starting 1.3.3 release the default password now is “CRAFT”, in the previous releases it was empty. Now to access to the “Local Procedures” the user should enter the password and then “Local Procedures”. For example there is a phone with default password and we would like to configure the phone by “ADDR” procedure then the full command will be:
MUTE, CRAFT ADDR #

Or;
MUTE, CRAFT VIEW #
MUTE, CRAFT RESET #
MUTE, CRAFT CLEAR #
MUTE, CRAFT <every old command that ever worked> #

Avaya_Red.gif

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged (Avaya Search tool )
______________________________________
 
That sucks :)
But it is now the same as with the 96xx phones.
The screen is too small so i understand it but i don't like it.
Thanks.


BAZINGA!

I'm not insane, my mother had me tested!

 
Thnx Bas,

I'm just updating 16xx phones to version 1.330D on a customer site, so this comes in handy!

Grtz,
Ronald
 
This is a nasty known issue:

While upgrading the 1616 IP Deskphone to
release 1.3200, if there are Button Modules
(BMs) attached to the 1616 IP Deskphone
being upgraded, then the BMs will also be
upgraded.
Note: You will need to carry out the following
procedure, when updating phones with more
than one Button Module attached.
When the BM software is being upgraded,
each of the BM LEDs will turn ON and then
OFF in a sequential fashion. The sequence will
stop after the 19th LED has turned ON as if
the upgrade process has stopped. The phone
will display the messaging, “Updating, Do not
Unplug”, while the upgrade is going on.

After the first Button Module has upgraded,
the LEDs on the second Button Module may
appear to start blinking RED and GREEN. But
to force the second Button Module to upgrade,
you must press a button on the FIRST Button
Module to start the upgrade of the SECOND
Button Module. The SECOND Button Module
upgrades with the same sequence of LEDs’
activities as the first Button Module.

If a phone is registered with an IP office,
it may have a 3rd button module
attached. In such case, the Third Button
Module must be disconnected before the
phone is upgraded to the new software.
If this is not done, and the phone is
updated before disconnecting the 3rd
Button Module from the phone, the
THIRD Button Module might become
dysfunctional during the upgrade and it
cannot be revived. The THIRD Button
Module has to be upgraded independently
by connecting it to any other 1616 phone
or by connecting it to the same phone as
above, but only after the first two button
modules have been disconnected.
It should be noted that Avaya doesn’t
recommend connecting/disconnecting
Button Modules to/from the phone, while
it is powered up.


Access the ‘A’ menu to check the version of
Button Module software, and to confirm if all
the button modules have been upgraded. It
should display: GBM32_B_1_1_0
Click to expand...




BAZINGA!

I'm not insane, my mother had me tested!

 
give the man a star for the info.

one from me bas and congrats for 2 years in the company :) hope my info is correct

Joe W.

FHandw, ACSS (SME), ACIS (SME)



Interrupt the silence only if you improve it by saying something, otherwise be quiet and everybody will be grateful.
 
I think that is true as i left one month before that and i am two years and one month working for my new boss :)


BAZINGA!

I'm not insane, my mother had me tested!

 
Thanks Westi, and it's 2 years already. Time flies when your having fun!
tlpeter and intrigrant left the company where i work now. They went both to a different reseller and i'm still on my own doing avaya at a disty. I wish i had more time to play with the stuff but it's ok. It funny but we also do siemens and other brands. For siemens there are four guys doing the job against me for avaya. And i have less shit over me than those ather four. I thought Avaya had a lot of bugs but siemens is worse! (It's not like the old days anymore)

Avaya_Red.gif

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged (Avaya Search tool )
______________________________________
 
Bas, i can report some more if you want :)
About those difference between the Siemens and Avaya, Intrigrant just said to them that avaya is just good thus why there are less calls :)


BAZINGA!

I'm not insane, my mother had me tested!

 
Status
Not open for further replies.

Similar threads

rudy_avaya
  • Locked
  • Question
Avaya 1616-L w/ BM32 Issues
Replies
2
Views
126
CMUK
CMUK
Davide G.
  • Question
Change firmware handset Ascom d43 to Avaya 3730
Replies
2
Views
260
Shaun E
Shaun E
Rolofhof
  • Locked
  • Question
Latest Avaya DECT Firmware versions
Replies
5
Views
253
OmegaStar
OmegaStar
Mani66
  • Locked
  • Question
J169 Handset is mute
Replies
1
Views
100
sizbut
sizbut
teletechman
  • Locked
  • Question
K155 phone firmware 1
Replies
4
Views
167
Shaun E
Shaun E

Part and Inventory Search

Sponsor

Back
Top