Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

FastRAD

Status
Not open for further replies.
ptstechnician

ptstechnician

Vendor
Jun 28, 2006
895
US
The FastRad is set to Auto Answer/Line 165/6 rings. Line 165 has the correct received digits but when I call the DID, the receptionist answers (they have full AA). The password and system id have been assigned. I was onsite yesteday and backed up the switch, so I don't know what I'm missing?
 
Sort by date Sort by votes
sounds like DTR to Prime is set for that line. Try turning that off for that Target line or better yet make the RADs ext the prime set.
 
Upvote 0 Downvote
Sound like reception has 165 assigned too or is the prime set.

Change prime set to the RAD's ext or have the RAD answer on 0 rings.


 
Upvote 0 Downvote
Another odd thing about this problem, I looked into Maintenance on Port 128 (where the Rad is connected to) & it shows a M7310 for the device. I thought it was supposed to show RAD?
 
Upvote 0 Downvote
Ex - The least amount of rings you can assign in the rad programming is 6. What about the device showing M7310?
 
Upvote 0 Downvote
I was wrong, it's 6 seconds not 6 rings. I just looked in the FastRad install guide and the Answer Delay says 6-60 seconds. I guess my ultimate question is, why is the call going to the operator and why does it show M7310 in Maintenance?
 
Upvote 0 Downvote
If its an older Fast Rad I remember they had to be upgraded to accept the higher target line numbers.
 
Upvote 0 Downvote
You might want to see if the A/A is answering that line under F.983...should be set fot no.
 
Upvote 0 Downvote
What are your answers to my questions above???????

And what if reception does not answer? what will answer after that and how many rings?


 
Upvote 0 Downvote
another place I found that target lines have had troubles is when the system is using one of the services. all the target lines have ext 21/221 as the control set.

another default for target lines is the primeset goint to the attendent. like noted above, make sure you kill line 165's control set, remove the primeset and make sure that it does not appear on the attendents phone and you shold be gold.

----------------------------
JerryReeve
Communications Systems Int'l
com-sys.com

 
Upvote 0 Downvote
In 2001 there was a patch issued for Fast Rads that were not answering on PRI lines. Nortel still has the patch. Sorry I don't know the number.

NARSBARS
 
Upvote 0 Downvote
Its called Fastrad firmware update. I have a disc with it on but it must be corrupted. I cant open it or copy it or do anything else with it. Maybe its still available for Nortel.
 
Upvote 0 Downvote
If you can't find it, post and I will check for a copy.

NARSBARS
 
Upvote 0 Downvote
Just got a copy of the firmware update from my tech support. Thanks.
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

Macgyver16502
  • Locked
  • Question
Nortel MICS FastRad help
Replies
2
Views
92
Macgyver16502
Macgyver16502
doughonea
  • Locked
  • Question
FastRAD over Ethernet
2
Replies
23
Views
264
MarkusSilver
MarkusSilver
mikefletcher85
  • Locked
  • Question
FastRAD Connection issues
Replies
13
Views
135
mikefletcher85
mikefletcher85
comguy19
  • Locked
  • Question
Nortel Fastrad firmware upgrade 1
Replies
4
Views
91
comguy19
comguy19
varrius
  • Locked
  • Question
MICS 7.1 not holding settings after restart - even after FastRAD/NRU restore
Replies
2
Views
47
varrius
varrius

Part and Inventory Search

Sponsor

Back
Top