-
1
- #1
TekceteraSupport
Vendor
****EXTREMELY IMPORTANT ****[/color red] Please note this is assuming that the IP Office is already on R3.1.65. If you have not upgraded to this yet please do so before continuing.
*** This info is taken from Avaya Tech Bulletin #71 (7/24/06) *** Just thought would be nice to have here!
7.2 Upgrade Instructions
To upgrade the Control and Expansion units do the following:
1. Install the Admin Suite as normal. Do not open the Manager application yet.
2. Open the Manager and ensure that you have received and made a backup
copy of the latest IP Office configuration. If for any reason the upgrade fails,
the current configuration may be erased, so a backup copy is essential.
3. To upgrade a 406v2 to 3.2 you must upgrade to an interim 3.1(999) build.
Follow these steps: In Manager select File | Change Working Directory.
Under the Directories Tab click the browse button next to Binary Directories
(.bin files). Expand the Manager folder, and then expand the 406v2 folder.
Highlight the v3_1_999 folder and click ok. The following will now appear in
your binary directory window.
C:\Program Files\Avaya\IP Office\Manager\IP406v2\V3_1_999
Click ok. Proceed with upgrade by going to File | Advanced | Upgrade. This
will start the UpgradeWiz application.
4. After a few seconds the upgrade wizard should show the Control and
Expansion units found. The list shows the current software levels of the units
and the level of the appropriate bin file that is available in the Manager/Binary
working directories.
5. The current version and available versions are displayed. Tick the check box
under Name if it is not already ticked then click on Upgrade.
Note: If upgrading the loader the version shown will be 3.1 (999), at this stage
only upgrade the main unit, do not upgrade the expansion modules as well.
6. Enter the password of the existing configuration (not the default). Click OK
and the upgrade process will begin. When the upgrade wizard informs you
that all units have been upgraded click OK and close down the upgrade
wizard.
7. You have just upgraded the loader you now need to upgrade to version 3.2.
In Manager select File | Change Working Directory. Under the Directories Tab
click the browse button next to Binary Directories (.bin files). Highlight the
Manager folder. Click OK.
8. Now follow steps 4-6 again to upgrade your system to IP Office 3.2.
Hope this helps!
Tekcetera Support Staff
*** This info is taken from Avaya Tech Bulletin #71 (7/24/06) *** Just thought would be nice to have here!
7.2 Upgrade Instructions
To upgrade the Control and Expansion units do the following:
1. Install the Admin Suite as normal. Do not open the Manager application yet.
2. Open the Manager and ensure that you have received and made a backup
copy of the latest IP Office configuration. If for any reason the upgrade fails,
the current configuration may be erased, so a backup copy is essential.
3. To upgrade a 406v2 to 3.2 you must upgrade to an interim 3.1(999) build.
Follow these steps: In Manager select File | Change Working Directory.
Under the Directories Tab click the browse button next to Binary Directories
(.bin files). Expand the Manager folder, and then expand the 406v2 folder.
Highlight the v3_1_999 folder and click ok. The following will now appear in
your binary directory window.
C:\Program Files\Avaya\IP Office\Manager\IP406v2\V3_1_999
Click ok. Proceed with upgrade by going to File | Advanced | Upgrade. This
will start the UpgradeWiz application.
4. After a few seconds the upgrade wizard should show the Control and
Expansion units found. The list shows the current software levels of the units
and the level of the appropriate bin file that is available in the Manager/Binary
working directories.
5. The current version and available versions are displayed. Tick the check box
under Name if it is not already ticked then click on Upgrade.
Note: If upgrading the loader the version shown will be 3.1 (999), at this stage
only upgrade the main unit, do not upgrade the expansion modules as well.
6. Enter the password of the existing configuration (not the default). Click OK
and the upgrade process will begin. When the upgrade wizard informs you
that all units have been upgraded click OK and close down the upgrade
wizard.
7. You have just upgraded the loader you now need to upgrade to version 3.2.
In Manager select File | Change Working Directory. Under the Directories Tab
click the browse button next to Binary Directories (.bin files). Highlight the
Manager folder. Click OK.
8. Now follow steps 4-6 again to upgrade your system to IP Office 3.2.
Hope this helps!
Tekcetera Support Staff